ATMEGA16驱动KS1080的192*64的液晶，图形显示

时钟芯片ds1302 c51源程序-clock source decoder chip ds1302

8051串口通信的单片机程序,使用C语言和VB语言.-8051 single-chip serial communications, the use of C language and VB language.

AVR_Meag8单片机控制三基色的LED，C源代码，包含电路原理路。-AVR_Meag8 single-chip control of trichromatic LED, C source code, including the principle of the road circuit.

51单片机的源程序集，有存储器，点阵式液晶，进制转换，led,ad等。-51 SCM source collection, storage, dot-matrix LCD, the base for the conversion, led, ad so.

x5045有四种功能：分别是上电复位、看门狗定时器、电源电压监控和块锁保护串行eeprom的功能， 该程序通过改变控制寄存器的参数可以实现看门狗定时器监视电压和设置保护rom区，每次复位后 地址计数器都是该区的首地址（个人观点），即断点地址。 问题：其实对该芯片的应用还是很模糊-x5045 four functions : the reduction of electricity, watchdog timer, Supply voltage control and protection block serial eeprom lock function, The procedure by changing the parameters of control register can be achieved watchdog timer and set up surveillance voltage protection rom, After each reset address counter area is the first address (personal view), breakpoint address. Question : In fact, the application of this chip is still very fuzzy! !

飞思卡尔S12 系列单片机系统硬件设计，详细介绍了该单片机的硬件使用，为全中文，MC9S12DG128B 有16路AD 转换，精度最高可设置为10 位；有8 路8 位PWM 并可两两级联为16 位精度PWM，特别适合用于控制多电机系统。它的串行通信端口也非常丰富，有2 路SCI，2 路SPI 此外还有IIC，CAN总线等端口，并且采用了引角复用功能，使得这些功能引角也可设置为普通的IO 端口使用。此外 它内部还集成了完整的模糊逻辑指令，可大大简化我们的程序设计。-Freescale s S12 family of single-chip microcomputer system hardware design, detail the use of single-chip hardware for the whole Chinese, MC9S12DG128B 16 Road AD conversion, the highest precision can be set to 10 are 8 and 8 PWM 22 Alliance for the 16-bit precision PWM, is particularly suitable for controlling multi-motor system. Its serial communication ports are also very rich 2-way SCI, 2 road SPI in addition to IIC, CAN bus, such as ports, and using the primers angle multiplexing function, so that these functions can also be cited angle is set to normal IO port to use. In addition, it also integrates the internal integrity of the fuzzy logic instructions, can greatly simplify the design of our procedures.

实现多个数字滚动，移位显示，当按下某个按键时，会将对应于端口的数值送入低位数码管显示-To achieve more than the number of rolling, shift display

这是运用MSP430单片机 对键盘进行判别的程序 运用单片机引脚的中断功能 使得只用一次扫描就可以 识别键盘码 -This the use of the keyboard MSP430 the procedures for identifying the microcomputer-pin interrupted feature allows only one scan can be identified keyboard code

一个简单的C51控制5位显示的程序,还有控制摩尔开关的程序大家可以-a project about C51

基于at89c2051的方波发生器，MAIN: MOV SP,#60H 设置SP指针 MOV R0,#50H 显示缓冲区首地址时50H ML0: CLR A MOV @R0,A 显示缓冲区清零 INC R0 CJNE R0,#55H,ML0-AT89C2051 based on the square-wave generator, MAIN: MOV SP,# 60H Set SP pointer MOV R0,# 50H shows that the first address buffer 50HML0: CLR A MOV @ R0, A display buffer cleared INC R0 CJNE R0,# 55H, ML0