To achieve steering boot automatically be converted to 0, through the microcontr...

基于51单片机的CA1602A液晶显示,串行传输,键盘编码等源代码-Based on MCU 51 CA1602A liquid crystal display, serial transmission, the keyboard coding source code

本系统是一个设计较完善的家用全数字功率放大器。它采用了美国APOGEE公司最新的DDX直接数字放大技术，音质直逼高档模拟放大器，同时，为了扩大使用范围，系统进一步集成了模拟音频输入通道，便于没有数字音频信号的用户使用该系统。操作方面采用了大型的128*64点阵液晶显示模块和非常方便易用的旋转编码器，同时更具有遥控功能。软件方面，以Atmega16单片机核心，采用了全中文菜单显示，由旋转编码器和遥控器作为输入设备，旋转编码器和遥控器均可实现全功能的操作。-This system is a better designed home all-digital power amplifier. It uses the U.S. APOGEE" s latest DDX Direct Digital Amplification technology, sound quality almost equal to high-end analog amplifiers at the same time, in order to expand the scope of application, the system further integrates the analog audio input channels, there is no digital audio signals to facilitate users of the system. Operational use of a large 128* 64 dot matrix LCD display module and very easy to use rotary encoder, but also has a remote control function. Software, in order to Atmega16 microcontroller core, which features a full Chinese menu display by the rotary encoder and remote control as input device, rotary encoders and remote controls can achieve a fully functional operati

基于89s51的keil跑马灯工程，程序虽然简单，但是它的经典程度不亚于软件开发中的“hello word”，单片机汇编编程者不妨参考一下。内附proteus完整的仿真文件。-Based on the keil Marquee 89s51 works, the program is simple, but it is no less than classic software development in the " hello word" , the compilation of single-chip programmers may wish to reference. Proteus simulation containing the complete document.

跑马灯程序,单片机初学者入门毕用的程序,里面代码已运行过,无误.-Marquee procedures Singlechip beginners used to complete entry procedures, which the code has been in operation, and correct.

利用单片机串口通信编译一个程序在打开时向电脑发送问候语-To compile a single-chip computer serial communication program is open to the computers to send greeting

51单片机及其C语言程序开发实例第7章节-51 SCM and its C language program to develop examples of section 7 of chapter

电机控制的程序例程，方便大家在座相应的工作中应用-Motor control routine procedure to facilitate the work of everyone here the application of the corresponding

一个很好用的密码锁程序，MCU用的是EM78P447，经试用非常可靠，提供给想学习EMC的用户使用，如有需要原理图的请发邮件到micheal23@sohu.com,注：需注明LOCK原理图-good with a password lock procedures, the MCU is EM78P447, tested very reliable, available to want to learn EMC users, if necessary schematic please send mail to micheal23@sohu.com, Note : LOCK be annotated diagram

本程序运行于C8051F330，功能为接收遥控器发出的红外信号，然后等待上位机通过I2C总线来读取。IR数据接收完毕后，不再采集新的IR数据，一直等待上位机将数据取走后才开始准备接收新的IR数据-this program running on the C8051F330, functional remote control device to receive the infrared signal, Then wait for the PC through the I2C bus to read. IR data receiving end, not the acquisition of new IR data have been waiting for the PC will be removed after data began preparing to receive the new IR data

基于单片机的程序，利用18B20测温，并通过1602液晶显示，并有检测18B20是否正常工作的功能。-Based on SCM procedures, the use of 18B20 temperature, and liquid crystal display 1602, and 18B20 Detect Whether or not there is a normal job functions.