LCD12864中文资料

WebCam Viewer Camera Server Version 1.0.5 Chipsbrain Engineer Final Release -Address WebCam Viewer Camera Server Version 1.0.5 Chipsbrain Engineer Final Release

使用51模拟I2C总线对CH450完成对6位LED数码管显示的操作。使用LED驱动芯片可分担51的工作量。-The use of 51 analog I2C bus on the CH450 completed six LED digital tube display operation. The use of LED Driver IC 51 may share the workload.

linux device driver for fifo algorithm

如果想自制一个自己的BOOTLOADER，那么就可以参照这里在ADS下的工程文件。只需稍加修改就可以变为自己的BOOTLOADER了.-If you want to made an own BOOTLOADER, then it can refer to here under the ADS project file. Just a little modification can be turned into its own the BootLoader.

modbus在工业控制网络上的应用,介绍了有关modbus和modbus tcp的有关内容.-modbus up in the industrial control network applications, the introduction modbus and modbus tcp relevant content.

mcs51测试子程序-mcs51 test subroutine

基于ARM7TDMI的uClinux移植,44b0x-uClinux transplantation, 44b0x

FPGA verilog PS2 鼠标控制LED   PS2接收模块（电脑接收，鼠标发送） PS2_CLK信号由PS2设备产生,即鼠标在产生时钟的同时向主机送出数据，主机在PS2_CLK信号的下降沿读取(锁存)每个位。/*标准的鼠标有两个计数器保持位移的跟踪:X位移计数器和Y位移计数器。**可存放9位的2进制补码，并且每个计数器都有相关的溢出标志。**它们的内容连同三个鼠标按钮的状态一起以三字节移动数据包的形式发送给主机。**位移计数器表示从最后一次位移数据包被送往主机后有位移量发生。**位移计数器是一个9位2的补码整数。它的最高位作为符号位出现在位移数据包的第一个字节里。

红外遥控码的接收程序，适用于pt2222,nec 6211 等--Receiver program for remote infrared encoding. It could be used in pt2222, nec 6211, and etc.

本系统利用集成智能温度传感器测量温度，采用光纤传输温度信号。系统由单片机（HT46R24）控制温度传感器（DS18B20）的温度采集。当有采集温度的指令的时候，才启动温度传感器并采回其数据，在没有进行温度采集的时候，将通过抬高温度传感器的地，关断其工作电源，如此可以降低系统的功耗。系统将每一次采集回来的数据与前一次的数据比较，若温度变化超限或温升超标，立即发送上述温度值；否则，累加到采集了一定的次数，再向主机发送最新温度值。-The system uses an integrated smart temperature sensors measure temperature, using optical fiber transmission temperature signal. System consists of microcontroller (HT46R24) controlling the temperature sensor (DS18B20) the temperature of collection. When a collection of instructions, when the temperature before start-up temperature sensors and taken back to its data, collected in the absence of the temperature when the temperature sensor will raise, the turn-off the power of their work, so you can reduce system power consumption. The system will come back every time collecting data and previous data comparison, if the temperature changes or temperature exceeding overrun immediately send the temperature value otherwise accumulate to collect a certain number of times, again