SCI exam in the enviroment of TMS2407

1）能够输出锯齿波，三角波，正弦波，脉冲波. （2）能根据键盘命令进行波形之间的切换. （3）能对输出的波形频率进行调节。 -1) can output sawtooth, triangle wave, sine wave, pulse wave. (2) according to the keyboard command to switch between waveforms. (3) can adjust the output waveform frequency.

MSP430F5438初始化程序,针对于MSP430F5438 编写的底层驱动，其中包含URAT,TIMEA,TIMEB,AD等模块的初始化

开发嵌入式实时系统很好的参考-develop embedded real-time systems makes good reference

eb55板子例程for ads-eb55 plank routines for ads

用PIC18xxx系列单片机实现直流电机伺服控制的源代码及详细文档-MCU with PIC18xxx Series DC motor servo control of the source code and detailed documentation

PLC实验设计交通灯完整程序及过程分析,是浙大一门课程的大作业-PLC traffic lights complete experimental design procedures and the process of analysis, is a curriculum Zheda big operation

总的来说，在uClinux上的开发和标准Linux还是很类似的。通常可以按照下面的步骤去设计和调试： 建立基于以太网的开发环境； 如果所设计的程序和硬件的关联不大，那么一定要在标准Linux上先编译和调试通过。灵活地使用gcc和gdb将大大节省时间； 将x86上的GCC编译好的应用程序用交叉编译工具来编译；如果编译时发现错误，那么很可能存在以下问题： 交叉编译器或库文件的路径不正确；最彻底的解决办法是重新装一次编译器； 遇到库不支持的函数；此时需要自己把函数的实现做成另外一个库供应用程序使用。如果是uClinux本身不支持的调用，那么就需要改写代码了。-Overall, the uClinux on the development and standard Linux is still very similar. Usually can use the following steps to design and debug : Ethernet-based development environment; If the design of the procedure and not linked to the hardware, then it must be the first standard Linux compiler and debugging through. Flexibility in the use of gdb and gcc will greatly save time; X86 will be on the GCC-compiled application with cross-compiler tool to compile; If you compile time error is found, it was very likely that the following issues : cross-compilers or libraries are not the correct path; The most radical solution is a re-installed time compiler; encountered does not support functions; At this time the need to

AT91RM9200的USB host和USB device的代码ADS1.2. USB-Device测试程序: 因为程序运行在SDRAM中，所以要先初始化SDRAM（可用basic boot程序初始，之后不能复位或断电），再运行此程序，程序运行后连接USB端口，计算机会提示检测到新硬件，安装硬件驱动程序atmusb6119.inf 后计算机会把USB端口虚拟为一个串行的端口使用-AT91RM9200 the USB host and USB device code ADS1.2.USB-Device test procedure: Because the procedure is running in SDRAM, and so we have to initialize SDRAM (available for the initial basic boot procedure, followed by Can not reset or power off), then Run this program, the program to run after connecting USB port, the computer will be prompted to detect the new hardware, installing hardware drivers after the computer will atmusb6119.inf virtual USB port to a serial port to use

datasheet lcd hd 44780

Linux系统函数 书籍语言： 简体中文 书籍类型： 系统专区 授权方式： 免费软件 书籍大小： 52 KB -Linux system function books Language : English books Type : System Precinct license : free software books Size : 52 KB