开发流程

采用UART方式0与LM74通信。 用C8051f020的P0.7作片选，主机通过TXD发送时钟信号，实现同步通信,半双工.RXD 作双向数据线.用六位数码管显示LM74采集的温度值-The use of UART communication mode 0 and LM74. P0.7 used for the C8051F020 chip select, host TXD sent through the clock signal, to achieve synchronous communication, half-duplex. RXD for bi-directional data line. With six digital tube display LM74 temperature collected

usb开发工具周立功公司下载很好用的一个软件-development tools usb Ligong weeks to download a very good company with a software

USB带宽测试的程序，针对CY7C68013的USB2.0接口芯片，编译环境为KEIL -USB bandwidth test procedures against CY7C68013 USB 2.0 interface chip, compile environment for KEIL

急救车与交通灯）（1）南北与东西方向，每个方面由红黄绿三个灯控制（2）南北向：　红（30秒），黄（5秒），绿（25秒）　　　东西向： 红（35秒），黄（5秒），绿（25秒）　　　上述基本参数可以根据实际情况自行调整，灯的变化规律与实际路口规律相同，绿灯在最后5秒钟时，黄灯亮，然后红灯亮，不允许两个方面同时亮绿灯。（3）绿灯的时间显示在数码管上进行显示。（4）可以通过一个开关控制，当开关信号为0时，整个交通灯全灭提高要求：（1）设计一个紧急控制开关信号，当紧急开关信号为1时，两个方向的灯全为红灯。紧急开关撤消后，按照开关按下之前的状态继续运行（其参数要保存）。（2）设计一个夜间行车开关，当开关按下后，两个方向都只有黄灯闪烁，其它灯熄灭。（3）设计两个方向的亮时时间可调。-emergency vehicles and traffic lights) (1) North and South and east-west direction, each with three yellow-green from red lights control (2) to the north and south : red (30 seconds), yellow (5 seconds), Green (25 seconds) to things : red (35 seconds), yellow (5 seconds) Green (25 seconds) above basic parameters can be adjusted to the actual situation, the light changes with the actual law of the same intersection, the green light in the final five seconds, the yellow light is on, and then a red light, bright, not two fronts simultaneously bright green. (3) the green light at the time displayed on the digital display control. (4) can be controlled by a

LCD T6963驱动程序 LCD T6963驱动程序-LCD Driver T6963 T6963 LCD Driver T6963 LCD Driver

自己写的ATmega16单片机驱动1602液晶的头文件，本人已测试通过，不错！-himself wrote the ATmega16 LCD Driver 1602 for the first document, I have been tested, yes!

基于2407平台的spi串行通讯常用例程 -2407 platform based on the commonly used 20 serial communication routines

ARM2410 step motor control ARM2410 step motor control ARM2410 step motor control -ARM2410 step motor controlARM2410 step motor controlARM2410 step motor controlARM2410 step motor controlARM2410 step motor controlARM2410 step motor controlARM2410 step motor controlARM2410 step motor controlARM2410 step motor controlARM2410 step motor controlARM2410 step motor controlARM2410 step motor controlARM2410 step motor control

温度检测：LAB200系统下，温度传感器仿真-Temperature detection: LAB200 system, temperature sensor simulation

用C51语言开发，相当有趣，附详细文档及硬件电路图-with C51 language development, very interesting, with detailed documentation and hardware circuit