基于VRS51L3074的TC35短信息模块驱动程序,程序内有完整的中文字库,支持中英文模式....

安装在手机里的安全的免费读书软件，目前装机量已达1500万，并被内置到诺基亚、摩托罗拉、多普达等手机中。用户的手机在安装掌上书院之后，可以阅读保存在手机里的各类资料-e book reader

一个新颖的自动调节匹配电阻阻值器，内有原理图,可供在家参考。-A novel resistance to match the automatic adjustment device, with a schematic diagram for reference at home.

在有线电视中实现程控有源滤波器设计。为了充分利用设备和传输线,需要一种具有频率选择的网络―滤波器,将同一线 路上不同的信号分开,在电视机中也需要不同的滤波器(即选择有用信号,抑制无用信号) 。下面利用8051 单片机与12 位分辨率的DAC1208 数模转换芯片相结合的系统实现时间常数可程控有源滤波器设计,阐述了硬件结构与软件设计-In cable television in the realization of program-controlled active filter design. In order to make full use of equipment and transmission lines, the need for a frequency selective network- filter, the same lines separate different signal in the TV also requires a different filter (ie, choice of useful signals and suppress unwanted signals). Following the use of 8051 and 12-bit resolution digital-to-analog converter DAC1208 chip combining system time constant can be program-controlled active filter design, the hardware structure and software design

直流电机调速实验C语言程序,使用L298N驱动-DC Motor Speed Experiment C language program, use the L298N drivers

智能车的马达控制程序,通过串口控制车的加速减速等。-This file is for Motor of Intellengence Car.

单片机控制网络芯片进行通信 （内容包括rtl8019as的驱动程序，uip协议栈，电路原理图，tcpip.h文件，pic单片机通过8019as进行通信的完整论文）-SCM control network chip communication (including rtl8019as driver, uip stack, circuit schematics, tcpip.h file, pic microcontroller to communicate through 8019as the full paper)

利用51系列单片机实现四种波形，正弦波、方拨、阶梯波、三角波，采用开关电路实现四种波形转换、放大电路实现波形幅度可调。通过编程实现仿真。-51 Series MCU realize the use of four types of waveforms, sine, square dial, ladder wave, triangle wave, the use of switching circuits to achieve the four waveform conversion, amplifier circuit realize adjustable waveform amplitude. Through the realization of simulation programming.

TFT 驱动 T100DEMO程序.做protable DVD的朋友可以参考一下.-T100DEMO TFT-driven procedures. Do protable DVD can refer a friend next.

本设计的由单片机控制的自动加料系统是与料斗式干燥机配套的加料系统。根据加料工艺要求，其工作原理是：先将真空管关闭，启动电机，用低真空气流将塑料树脂粒子送入真空管，电机停转，再将粒子排入料斗，如此循环。-The design of single-chip microcomputer controlled by the automatic feeding system with hopper dryer feed supporting system. Charging process in accordance with the requirements of its working principle is: first vacuum tube to close, start motor, using low vacuum plastic resin particles will flow into the vacuum tube, the electrical switch to stop, and then particles into the hopper, and so the cycle.

不开销缓存RAM的430Flash读写程序-Do not spend the 430Flash cache RAM read and write procedures