介绍利用VB6串行通信编程的方法，对采用了RS

vc++6.0写的串口操作的类-vc 6.0 write operation of the serial category

串行口是计算机一种常用的接口，具有连接线少，通讯简单，得到广泛的使用。常用的串口是RS-232-C接口(又称EIA RS-232-C)它是在1970年由美国电子工业协会(EIA)联合贝尔系统、调制解调器厂家及计算机终端生产厂家共同制定的用于串行通讯的标准。它的全名是"数据终端设备(DTE)和数据通讯设备(DCE)之间串行二进制数据交换接口技术标准"该标准规定采用一个25个脚的DB25连接器，对连接器的每个引脚的信号内容加以规定，还对各种信号的电平加以规定。传输距离在码元畸变小于4%的情况下，传输电缆长度应为50英尺。 　　Linux操作系统从一开始就对串行口提供了很好的支持，本文就Linux下的串行口通讯编程进行简单的介绍.-computer serial port is a common interface, with connecting lines, simple communications, to be widely used. It is commonly used serial RS-232-C interface (also known as the EIA RS-232-C) it is in 1970 by the American Electronics Industry Association (EIA) Joint Bell System, a modem manufacturers and computer terminal manufacturers developed for serial communication standards. Its full title is "data terminal equipment (DTE) and data communications equipment (DCE) between serial binary data exchange interface technology standards," the use of a standard 25 feet to the DB25 connector, the connector pin of each signal content requirements, but also the right signal--

串口通信，MSComm控件，不是API，忘大家查证-Serial communication, MSComm control, not the API, everyone forgot to check

S3C2410ARM处理器的uCos2移植实验代码，包括移植，串口通信等。-S3C2410ARM processor code uCos2 transplant experiments, including transplantation, serial communications.

A/D转换－数据采集实验 * * A/D转换数据采集程序source file * * 运行步骤：1.在平台板的8位AD通道选择开关上 选定通道号 * * 2.程序运行后，转动电位器，观测数据的变化 -A/D converter-experimental data acquisition** A/D converter data acquisition program source file** Run steps : 1. The platform board eight AD channel selection switch on the selected channel,** 2. Running after turning Potentiometers, observational data changes

自己写的一个串口类,从CNCOMM改正过来的,精简代码,解决了只能事件方式下只能接收几个字符的问题-Himself wrote a serial type, from CNCOMM mistakes, to streamline the code, solve the incident only way to receive only a few characters in the issue of

计算机串口调试的小程序，可以监测串口的RTS,DSR活动-Computer serial port debugging applets, you can monitor the serial port of the RTS, DSR activities

在vb中用字符串的形式来处理串口协议，具有一定的通用性！本程序用来控制伺服电机，调试通过！-vb used in a string of serial form to the agreement, which have a certain commonality! Procedures used to control the servo motor, debugging through!

本文介绍了一种新的使用串行通信进行DSP远程在线编程方法。对设计中的主要技术：DSP与PC机的串口通信、Flash编程以及DSP自引导等进行了详细介绍。结合TI公司的TMS320VC33处理器，阐述了具体的实现方法-This paper introduces a new use of serial communications DSP remote online programming method. On the design of the main techniques: DSP and PC-serial communication, Flash programming as well as the DSP, such as self-guided introduction in detail. Combination of TI

将串口通讯协议存储为一个通讯文件，可是随时将存储通讯协议文件调入计算机运行与下位机通讯可以实现通讯对话，-Serial communication protocol will be stored as a communications document, but to keep the communication protocol storage document transferred to the computer is running and the next-bit machine communication can realize communication dialogue