此程序是用于AVR单片机驱动FLASH的,对于用AVR单片机进行开发的朋友,提供了一个例程,还有对于对使用FLASH没有经验的朋友也有很好参考价值...

一个单片机驱动红外通信的程序,很有意义.当然你也可以举一反三,用作无线通信,也可以仿照该程序做蓝牙通信协议-A single-chip driver infrared communications procedures, meaningful. Of course you can learn by analogy, for wireless communications, modeled on the program can also do Bluetooth communication protocol

时钟芯片ds12c887线片驱动程序，可直接应用-Clock Chip ds12c887-ray driver, can be directly applied

以上程序使用PIC12C508单片机，内部4MHZ时钟，4脚输入50HZ脉冲信号，7，6，3脚（GP0，GP1，GP4端口）为输出口。其中渐变部分是让灯慢慢的变亮（或灭--It uses PIC2C508 SCM, 4MHZ clock, 4 port is for inputting 50HZ signal, 7/6/3 port for output.

基于MICROCHIP PIC16F系列电动自行车控制源码.-MICROCHIP PIC16F series based on the control source for electric bikes.

本设计采用ATMEL公司的AT89S52单片机和红外遥控技术实现近距离无线通信的软硬件系统。为了使受控设备识别信号，设计一种数字信号编码系统，利用红外线将数字信号调制，而数据的解码则由另外的单片机完成，系统的实现简单。-This design uses ATMEL Corporation AT89S52 MCU and infrared remote control technology to achieve a short distance wireless communications hardware and software systems. Controlled equipment in order to enable the identification signal, the design of a digital signal coding system, using infra-red digital signal modulation, and data from other single-chip decoder completed, the system simple.

该实验是在“点到点无线通信实验”的基础上进行开发，节点A 作为发射模块，节点B 作为射频休眠实验的对象，PC 通过串口下达休眠和唤醒的指令给节点B，来实现对射频部 件的唤醒和休眠功能。串口的设置为波特率115200b/s，8 位数据位，1 位停止位，无校验位。-The experiment in the " point to point wireless communications experiment" based on the development and launch of the module as a node A, node B as a test object dormant radio frequency, PC through the serial port sleep and wake-up instructions issued to the Node B, to achieve the right wake-up radio frequency components and the hibernation feature. Serial port baud rate is set to 115200b/s, 8 bits of data bits, 1 stop bit, no parity bit.

计算机简单控制由软件和硬件组成。软件由Visual Basic 6.0编写。硬件主要由无线发送模块和单片机（C语言编写）构成。通过RS232界面与PC通信而实现无线控制系统。 主要功能是：通过遥控器连接PC机的"上下左右"按键 ,当电脑界面处于powerpoint界面下,能通过遥控器控制幻灯片的上下切换. -Simple control by the computer software and hardware components. Software prepared by the Visual Basic 6.0. Hardware mainly by the wireless sending module and single chip (C language) constitute. Through the RS232 communication interface with the PC wireless control system. Main function is to: Connect PC through a remote control machine up and down about button, when the computer interface in a powerpoint interface via remote control to switch slides up and down.

本文件是用51单片机设计电子琴的资料文件，且带有原理图-The present document is a single-chip design with 51 information paper flower, and a schematic diagram

飞思卡尔的编程资料，开发软件的调试，以及智能车路线识别系统文章。 -Freescale" s programming information, development of software debugging, and intelligent vehicle identification system routes the article.

学习C51时写的数码灯程序,提供给刚学单片机程序的朋友参考-When learning to write C51 digital light process, available to just school friends Singlechip procedure reference