单片机开发实例 很有用 是五十一的单片机 只要有c语言基础就可以上手...

一个基于时钟芯片1302的单片机时钟。使用伟福的仿真器编译通过，同时写入单片机后的硬件电路也好使。-1302 based on the clock chip microcontroller clock. Wei-fu of the use of the compiler through the emulator, at the same time to write after the single-chip hardware circuitry or so.

独立数码管计数，从0到99的计数，然后再清零。比较简单的代码。-Independent digital control counts, 0-99 from the count, and then cleared. The code is relatively simple.

单片机 mega16L 电池放电器源码-Singlechip mega16L battery source discharger

此程序为利用mage8 AVR 和EM4094实现读取TYPE B类型卡的C程序、读卡稳定、这个项目我们做了好久、非常不错的程序、很适合做这方面产品的朋友们参考-This procedure for the use of mage8 AVR and the EM4094 Read TYPE B to achieve the type of card C procedures, reader stability, the project we have done for a long time, very good program, it is suitable for products in this area refer to my friends

LCD1602的显示程序，用的是S51单片机，已通过调试。-LCD1602 display program, using a S51 MCU has passed debugging.

C8051F020/1/2/3混合信号ISP FLASH微控制器数据手册（中文的哦）-C8051F020/1/2/3 Mixed-Signal ISP FLASH MCU Data Sheet (Chinese, Oh)

C51对C6963C的驱动编程,包含具体的连接定义和汉字字库,我已经完全显示成功-C51 right C6963C driven programming, include specific definitions and connect Chinese character, I have fully demonstrates success

斜度测试程序 * 程序对应的硬件设置为：利而达MSP430-Test44x实验板，斜度计使用的 * 是ADXL202E，数字y连接TA1/P1.2,数据x连接P1.0/TA0,P4.6对应斜度计电源 * 每个方向的斜度显示时都占用三个字符， * 斜度范围为0~90,高于90的，斜度为(180－斜度）-Gradient procedures for the corresponding test procedures* for the hardware set up: Lee MSP430-Test44x of the board, of the use of gradient is the* ADXL202E, the number of y connecting TA1/P1.2, data x connect P1.0/TA0, P4. gradient of 6 corresponds to the power* of the gradient in each direction are occupied by shows that the three characters,* angle range of 0 ~ 90, more than 90, and slope for the (180- angle)

PC数字电压表的设计,原理图以及代码,设计文档.此数字电压表的优势在于可以通过串口将测量所得到的电压值传给PC机,这样的话有利用整个数据的采集与分析.上位机采取的是串口通信软件.-PC digital voltage meter design, diagram and code, Design Documentation. This figure voltage meter advantage is through the serial port will be measured by the voltage transmission PC, so is the use of the entire data collection and analysis. PC"s serial port communication software.

仿真步骤如下： 1、把3个帖子的内容分别保存为51t9py.c,51t9py_indexa.h,5py_mb.h，放在同一目录下，将51t9py.c加入工程编译 2、由于Keil的模拟串口是单字节显示，汉字显示为乱码，所以要加挂RICHWIN或RichView这种会重新刷新显示的中文平台，或手工刷新屏幕，所以请先到 http://www.pchome.net/dl/chinese.htm 下载RichView，安装运行 3、在Keil环境下可以直接按“Ctrl＋F5”键仿真，按“F5”全速运行，切换到在串口依次输入: // 64*.6 426***.5 98*.7 936.3 586.1 4826*.1 9464*.7 64*.6试试:-) 4、按键对应(根据我自己的手机设置的,全部在PC的小键盘操作)： -simulation steps are as follows : 1 and 3 respectively, the content of messages posted on the preservation of 51t9py.c, 51t9py_indexa.h, 5py_mb.h, on the same directory, will join the project 51t9py.c compiler 2, Keil is the simulation of single-byte Serial show , the Chinese showed gibberish, so need to add or RichView RICHWIN this show will re-set the Chinese platform, or manual refresh screen, so please download RichView http://www.pchome.net/dl/chinese.htm to install three operations in Central Keil Habitat can be directly "Ctrl+ F5" key simulation, according to the "F5" running full-speed, switched to the ser