开发环境为keil166，使用xc164cs从can接收数据 在串口定时发送

自己写的 STM32F10x的ADC和Timer驱动, 没有使用固件库。每秒通过串口UART输出当前ADC值。 应用范围: 因为不涉及IO口,所以此工程在STM32F1xx的任何主板上都可以运行。 编译器: IAR ARM 4.42A。 作者: w123456xy@sohu.com 15189792379。 -Write your own STM32F10x the ADC and Timer-driven, not using the firmware library. Second serial UART output current through the ADC value. Application scope: because they do not involve IO port, so this works on any STM32F1xx motherboard can run. Compiler: IAR ARM 4.42A. Author: w123456xy@sohu.com 15189792379.

系统以AT89S52单片机为控制核心，加以直流电机、舵机、光电传感器、火焰传感器和电源电路以及其他电路构成，设计报告完整，元器件选择比较恰当，制作的小车能完成题-AT89S52 Single-chip system for the control of the core, to DC motor, gear, photoelectric sensors, flame sensors and power supply circuit and other circuits, the design integrity of the report, more appropriate choice of components to produce the car to complete the title

简易数字电压表的设计,利用单片机AT89S51与ADC0809设计一个数字电压表，能够测量0－5V之间的直流电压值，四位数码显示，但要求使用的元器件数目最少。-Simple digital voltage meter design, the use of single-chip AT89S51 with ADC0809 to design a digital voltage meter, capable of measuring between 0-5V DC voltage value, four digital display, but requires the use of minimum number of components.

单片机89s51做的波形发生器，含PROTEUS仿真图，非常实用的波形产生源码！-89s51 do single-chip waveform generator, including PROTEUS simulation map, very useful source of the waveform generator!

keil 的相关资料，包括C语言标准和i2c总想的相关资料-keil relevant information, including the C language standards and i2c want relevant information

nokia5110 lcd 的 keil C51 驱动程序，支持英文和汉字的显示-nokia5110 lcd the keil C51 driver, in English and Chinese support for the show

DK3400_3420 USB R_W source code - Keil-DK3400_3420 USB R_W source code- Keil

51单片机开发的等精度数字频率计，实现计数0--51 Single-chip, such as the development of precision digital frequency meter, realize counts 0--

12232液晶模块的应用，该模块采用ST7920液晶控制芯片，编译菜用WinAVR2005.-12232 Application of LCD module, the module used ST7920 LCD controller chip, the compiler vegetable WinAVR2005.

利用单片机的定时器定时，令十字路口的红绿灯交替点亮和熄灭，实现主支路路口的交通信号灯控制（尽可能保持主线的畅通，即在通常情况下，保持主线的放行，只有在支线到达时，才放行支线），同时采用LCD显示倒计时时间及当前灯的状态-The use of MCU timer timing, so that the crossroads at the traffic lights turn out light and to achieve the main slip road junction traffic lights control (as far as possible the smooth flow of the main line, that is, under normal circumstances, to maintain the release of the main line, and only arrived at the branch only when the release branch), while using LCD display countdown time and the current state of light