单相电机变频驱动原码,采用DISPIC30芯片

看到最近大家都关心 usbhost 的实现, 论坛上能找到的代码仅是一些简单的 demo , 完整的源码级的协议层是找不到的 我就贡献一把, 将我前一段时间移植成功的 USBHost 代码奉上 注意事项 1. ohci 层移植自 u-boot-1.3.2-rc3 2. fat 层移植自 gba_nds_fat 3. 本代码只是我产品中的一部分, 使用 Keil RTL 操作系统, 任务为 void task_usb(void) __task 保证完整, 想要跑起来可能需要做些修改与测试-?#39 ??????#39 蠹??脊匦?usbhost 的实现, 论坛上能找??的

DEW POINT CALCULATION ROUTINE

基于Keil C平台的单片机源程序，用于检测ＤＡ５２９的程序，刚才用另一个邮箱mm0000ll@yahoo.com上传，麻烦站长帮忙改一下-Based on the Keil C source microcontroller platform for detecting DA529 procedure, just use another mail mm0000ll@yahoo.com upload, trouble station to help change the

电机测速源码程序，好使的已经通过测试了。非常精确-Motor Speed-source program, so that has passed the test. Very precise

UCOS在AVR单片机上的移植工程,开发环境为ICC.-UCOS in AVR on the transplant works, the development environment for the ICC.

周立功7290（zlg7290）i2c芯片 在uclinux上的驱动程序。已经移植成功，包括可执行文件-7290 (zlg7290) Basis i2c chip in on the driver. Transplantation has been successful, including executable files

cxa3050芯片控制程序，本人用的是Ｃ语言编写，芯片用的是ＡＴ８９Ｃ５１-cxa3050 chip control procedures, I used the C language, the chip is AT89C51

用于蓝牙开发！基于hci的编程，可实现单片机对蓝牙模块的控制，从而实现蓝牙主从设备的连接和通信！-for Bluetooth development! Based on HCI programming can be realized right MCU Bluetooth module control, thereby achieving Bluetooth equipment from the main connection and communication!

仪器仪表使用GPIB接口程序！ 国内仪器基本很少用到的，我的绝对能用已经用于多台测试仪器。-Instruments GPIB interface program to use! The basic domestic equipment rarely used, and I definitely can use has been used for multiple test instruments.

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.