此文件包含通过微处理器8085和8086…..解释

MAX5403/5404/5405系列数字电位器的广泛应用，可用于AGC和可调参考电压电路-Digital Potentiometers MAX5403/5404/5405 series of widely used, can be used for AGC and adjustable reference voltage circuit

Atmel arm7有关USB应用的实例,可在IAR上面直接运行-Atmel arm7 Examples of applications on the USB can be run directly above in the IAR

Keeloq Workshop simple

需要加入ZLG7290库。可以在ZLG网站下载！ 在KEIL中调试通过！-the need for Wire. ZLG can download! Tuning in KEIL through!

powerpcb快捷命令，希望对大家有用-powerpcb quick order, everyone would like to be useful

采用MCP2515的CAN通信代码，适合8位、16位AVR单片机-MCP2515 using the CAN communications code, suitable for 8-bit, 16-bit AVR Singlechip

P1.7～P1.0接发光二极管L8～L1，要求利用单片机内部定时器1，按方式1工作，每0.01秒T1溢出中断一次。要求编写程序模拟时序控制装置。开机第1秒钟L1、L3亮，第2秒钟L2、L4亮，第3秒钟L5、L7亮，第4秒钟L6、L8亮，第5秒钟L1、L3、L5、L7亮，第6秒钟L2、L4、L6、L8亮，第7秒钟8个发光二极管全亮，……一直循环下去。fosc=11.0592MHz-P1.7- P1.0 then LED L1 to L8, by using a timer internal microcontroller, a work by the way, every 0.01 seconds T1 interrupted an overflow. Simulation prepared timing control device. Boot 1 seconds L1, L3- liang, two seconds L2- L4, L5 three seconds, L7- liang, 4 seconds L6, L8-liang, 5 seconds L1, L2, L5, L7- liang, 6 seconds L2, L4, L6, L8- , 7 seconds 8-LED whole ... has been the cycle continues. 11.0592MHz fosc =

在Iccavr软件平台上，提供一个具有通用性的 mega Bootloader，不同型号的AVR单片机只需要修改一下几个简单的配置参数就可以直接使用了，不需要再修改主程序。-In Iccavr software platform to provide a universal mega Bootloader, different models of AVR Singlechip you only need to modify a few simple configuration parameters can be used directly, no need to modify the main program.

C8051F040的HT1380操作时序，以及时间设置和LCD时间显示(显示小时和分钟)-C8051F040 operation timing of the HT1380, as well as set-up time and time LCD display (shows hours and minutes)

FIQ有FIQ_PWM、FIQ_TMA和FIQ_TMB三个中断源,当定时器A或B计满溢出时产生中断请求信号TA_TIMEOUT_INT或TA_TIMEOUT_INT,CPU响应后进入中断执行相应的子程序控制二极管发光。A口的低四位接LED灯，B口的低四位接LED灯.-FIQ has FIQ_PWM, FIQ_TMA and FIQ_TMB three interrupt sources, when the timer A or B when the expiration overflow interrupt request signal TA_TIMEOUT_INT or TA_TIMEOUT_INT, CPU response after interruption of the implementation of the corresponding subprogram control light-emitting diodes. A low population of four LED lights then, B I take the low four LED lights.