CRC8计算程序及检测程序，C语言，生成多项式：X8 + X2 + X + 1

本程序实现了mini pascal的一个编译的总过程。(the process of achieving a mini pascal translation of the total process.)

MAODV源码用于NS2网络仿真，内容齐全详细，想要学习的同学，可以看看包括MAODV implementation installtion package等内容

一本讲解C++优化方面的书籍。相信能给你收获。的(an optimizing C on the books. Can you believe that the harvest. The)

RTD2660 驱动程序源码

硬件资源: 1,DS0(连接在PA8)，DS1(连接在PD2上) 2,串口1(波特率:115200,PA9/PA10连接在板载USB转串口芯片CH340上面) 3,ALIENTEK 2.8/3.5/4.3寸LCD模块(仅支持MCU屏) 4,按键KEY0(PC5)/KEY1(PA15)/KEY_UP(PA0,也称之为WK_UP) 实验现象: 通过按键KEY_UP可以控制定时器AutoReloadTimer_Handle的开启，这个是 周期定时器，一旦开启就会不断的运行，直到按下KEY1将其关闭。按下KEY0 可以打开定时器OneShotTimer_Handle，这是个单次定时器，只会运行一次， 运行周期到了以后就会停止运行，除非按下按键KEY0将其再次开启。(Hardware resources: 1, DS0 (connected to PA8), DS1 (connected to PD2) 2. Serial port 1 (baud rate: 115200, PA9/PA10 connected on board USB to serial chip CH340) 3, ALIENTEK 2.8/3.5/4.3 inch LCD module (only supporting MCU screen) 4. Keyboard KEY0 (PC5)/KEY1 (PA15)/KEY_UP (PA0, also known as WK_UP) Experimental phenomena: The timer AutoReloadTimer_Handle can be turned on by keying KEY_UP. This is The periodic timer will run continuously once it is turned on until KEY1 is pressed to turn it off. Press KEY0 You can turn on the timer OneShotTimer_Handle, which is a single timer and only runs once. The run cycle will stop after that unless KEY0 is pressed to turn it on again.)

本播放器用于播放.vga格式的课件(大量西北工业大学的课件都是这种格式) 为了更好的使用本播放器，请注意以下几点： 1)视频文件(*.asf)必须和课件文件(*.vga)在同一个目 录下 2)同一节课具有相同的名字，例如01.asf对应01.vga， 反之亦然。 3)如有任何意见或建议请发邮件至dgx_lsyd3@163.com 或加QQ:259177377 (The player used to play. Vga courseware format (a large number of Northwestern Polytechnical University courseware is in this format) In order to better use of the player, please note the following: 1) the video file (*. asf) must be and courseware documents (*. vga) in the same directory 2) the same class with the same name, for example, 01.asf corresponding 01.vga, and vice versa. 3) If you have any comments or suggestions, please e-mail dgx_lsyd3@163.com or QQ: 259177377)

使用GUI绘制棋盘 在panel控件中调用paint事件(The use of GUI drawing board at the control panel to call the paint case)

p1.5脚控制灯。 当灯点亮是，把域值增大。 光传感器通过AD转换。 使用STC12C5404AD调试通过。(P1.5 pin control lights. When the lights lit is to increase the domain value. Optical sensor through the AD conversion. Debugging through the use of STC12C5404AD.)

可以产生幅度、频率可调的方波，频率50hz到1M(Can produce the amplitude, frequency adjustable Fang Bo, frequency of 50Hz to 1M)

转载libmodebus库的测试文件，从站是用软件测试的，如果要用单片机当从站，修改那八个字节的参数即可。用的是QT开发软件，可以修改mainwindows的内容。