登录
首页 » SCM » 这是我用C语言写的一个数字钟,他可以实现多种闹钟和秒表功能...

这是我用C语言写的一个数字钟,他可以实现多种闹钟和秒表功能...

于 2023-03-17 发布 文件大小:2.23 kB
0 146
下载积分: 2 下载次数: 1

代码说明:

这是我用C语言写的一个数字钟,他可以实现多种闹钟和秒表功能-This is because I use C language written in a digital clock, he can achieve a variety of alarm and stopwatch functions, etc.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 24高
    24位高精度A转换芯片 AD7710 源码 已成功用于液压自动控制系统五年-24 high-precision A conversion chip AD7710 source has been successfully used for hydraulic automatic control system for five years
    2022-12-06 23:10:02下载
    积分:1
  • C8051F020单片机的LCD显示程序,使用液晶显示器320 x 240的屏幕,驱动芯片…
    基于C8051F020单片机的LCD显示程序,LCD用的是320×240屏幕,驱动芯片为SED1330,采用C51编写-C8051F020 LCD display program, using the LCD 320 x 240 screen, driver chips for SED1330, prepared using C51
    2022-01-25 17:52:45下载
    积分:1
  • profibus从站模拟量接口模块设计.rar
    profibus从站模拟量接口模块设计.rar-Profibus station analog interface module design. Rar
    2023-02-25 20:10:03下载
    积分:1
  • 休眠模式下的AD转换,高速,10位,更低功耗
    休眠模式下的AD转换,高速,10位,更低功耗-Hibernation mode AD conversion, high-speed, 10, lower power consumption
    2022-03-21 22:10:25下载
    积分:1
  • 89S52作为USB键盘做核心,注意修改厕所…
    使用89S52为核心做的USB键盘,注意修改了一下windows设备描述符以及端点处理等就行了。用了一个4*4的小键盘,有0-9十个数字键, Num Lock键,Caps Lock键,Shift键,Ctrl键,Alt键,回车键等。 最多可以有三个键同时按下,如果相交的话,最多只能两个键按下-89S52 use as the core of the USB keyboard to do, pay attention to modify the look and the windows device descriptor, such as treatment endpoint on the list. Used a 4* 4 small keyboard, has the number keys 0-9 10, Num Lock keys, Caps Lock key, Shift key, Ctrl key, Alt key, enter key and so on. Can have up to three keys pressed at the same time, if the intersection, then a maximum of only two keys pressed
    2023-03-24 10:05:04下载
    积分:1
  • 51单片机产生锯齿波的程序
    51单片机产生锯齿波的程序-51 SCM procedures have Sawtooth
    2022-01-21 21:40:44下载
    积分:1
  • display driver chip HT1621 the bottom procedures C51
    显示驱动芯片HT1621的C51底层程序-display driver chip HT1621 the bottom procedures C51
    2022-02-20 00:17:54下载
    积分:1
  • 1.熟悉硬件仿真工具KD30的使用。 2.修改样本程序 SAMP1a,使无论在计数或停止计数时,按 SW3 均对计数值清零,并停止计数。 3.编制一个秒表程序,...
    1.熟悉硬件仿真工具KD30的使用。 2.修改样本程序 SAMP1a,使无论在计数或停止计数时,按 SW3 均对计数值清零,并停止计数。 3.编制一个秒表程序, 测试精度为0.1秒,按 SW1键启动计数,再按一次 SW1键停止计数。任何时候按 SW3 键停止计数,并对计数值清零。 4.按 SW1键后, 以 0.1 秒为单位开始计数,再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒,则计数值清零,回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.
    2023-08-01 05:40:03下载
    积分:1
  • 用TI单片机MSP430系列写的CRC检验程序,C语言
    用TI单片机MSP430系列写的CRC检验程序,C语言-Using TI single-chip MSP430 series written by CRC testing procedures, C language
    2022-05-16 21:55:09下载
    积分:1
  • 2.0TFT屏S6D0118driver的驱动程序及其点屏的资料
    2.0TFT屏S6D0118driver的驱动程序及其点屏的资料-2.0TFT screen S6D0118driver driver information screen and the point
    2022-05-09 08:40:40下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载