simulation C51 Serial Programming

一个C语言编写的单片机并口数据发送代码-an bunch of computer parallel port data transfer code programmed with C

《单片机仿真入门实用教程》实例(包括源代码) 单片机仿真教程。-"PROTEUS Practical Guide Getting Started" examples (including source code) Proteus-based simulation of single-chip microcomputer.

用vc++实现的双踪示波器程序源码 用vc++实现的双踪示波器程序源码. 用vc++实现的双踪示波器程序源码-With vc++ Realize the dual-trace oscilloscope program source with vc++ Realize the dual-trace oscilloscope program source code. Using vc++ Realize the dual-trace oscilloscope program source

介绍zlg7290的pdf，介绍得很详细，还有程序实例。-Introduction zlg7290 the pdf, very detailed introduction, there are instances.

定时器设置，适合初学者学习，演示定时器及中断，使用KEIL　C编写-timer settings for beginners to learn, and the timer interrupt demonstration, the use of C prepared KEIL

用DSP控制步进电机,DSP选用TMS320C240,-Stepper motor with DSP control, DSP selection TMS320C240,

P89C669存储实例: 说明： 1. inc 文件夹 是关于P89C669的头文件，在使用下面两个例子前，请首先将头文件拷到 ..KeilC51INC下. 2. Rom 文件夹 是关于P89C669的程序空间使用的例子，说明怎样利用大于64KB的程序空间。 3. Ram 文件夹 是关于P89C669的数据空间使用的例子，说明怎样在各个数据空间定义变量。 -P89C669 storage examples: Note: 1. Inc folder is on the first P89C669 documents, in the use of the following two examples, please first Kaodao header files .. KeilC51INC under .2. Rom folder P89C669 procedures on space use example of how to make use of the procedure is greater than 64KB of space. 3. Ram folder P89C669 data on space use examples to illustrate how the definition of data space in all variables.

程序描述：这个范例说明如何使用8051，以及汇编语言的程序连结， 当我们按下向上数的按钮之后，程序就会把0到9的共 阳7段显示器字型码存入AT93C46；如果我们按下向下 数的按钮之后，程序就会把9到0的共阳7段显示器字 型码存入AT93C46。 程序每一次重新开始执行时(Power on 或是Reset)，8051 会先从AT93C46当中读出最前面的10个位组，然后 就反复地将这10个位组的数据经由PORT 1送到1个 共阳七段显示器。*/-Procedure Description: This example shows how to use the 8051, as well as links to assembly language programs, when we pressed up a few of the button, the program will bring a total of 0-9 yang seven segment display font yards into AT93C46 if we press Next down the number button, the program will bring a total of 9-0 Yang seven segment display font code into AT93C46. Process to begin again each time when the (Power on or Reset), 8051 will start with AT93C46 were read out in front, 10-bit groups, and then repeated these 10-bit groups of data via the PORT 1 sent to a A total of seven-segment display Yang.* /

STM32串口操作源代码 STM32串口操作源代码 STM32串口操作源代码-STM32 serial operation serial port operation STM32 source code source code source code STM32 serial operation