凌阳单片机波形发生器的设计

嵌入式开发工具的使用方法，以及使用中搜遇到的问题-embedded development tools to use, and the use of the seizure problems encountered

自己写的 STM32 串口UART驱动, 不用固件库。超级终端界面按键时,自动回送。 应用范围: 因为不涉及IO口,所以此工程在STM32F1xx的任何主板上都可以运行。 编译器: IAR ARM 4.42A。 作者: w123456xy@sohu.com 15189792379。 -Write your own STM32 serial UART driver, no firmware library. HyperTerminal interface button, automatically send back. Application scope: because they do not involve IO port, so this works on any STM32F1xx motherboard can run. Compiler: IAR ARM 4.42A. Author: w123456xy@sohu.com 15189792379.

这个游戏是用ICCAVR编译的,KS0108液晶屏,19264的,共有12关,难度是递增的,可以选关玩,每过一关会有一个祝福语,目前还在调试阶段,先传一部分上来.图片是用手机拍的,不够清楚.-The game is ICCAVR compiled, KS0108 LCD, 19264, a total of 12 clearance, the difficulty is increased, clearance can choose to play, every one there will be a blessing related language, is still debugging stage, the first part of Chuan-up. picture was shot using a mobile phone, and not clear enough.

使用PROTEUS仿真的DS1302时钟,与主机同步显示时间,C编写-PROTEUS simulation using the DS1302 clock, display time synchronization with the host, C prepared

pic单片机驱动mcp2510源代码，采用picc编译器-pic Microprocessor mcp2510 source code, compilers used picc

avr 源代码 mega16 例程 大约30个 -avr source code mega16 routine about 30

单片机控制水温的汇编程序，通过加热开关控制水温并显示温度！-SCM temperature control the compilation process, by heating water temperature control switches and display temperature!

红外遥控接收 ORG 0000H LJMP START 转入主程序 ORG 0010H START: MAIN: JNB P2.2,IR LJMP MAIN 以下为进入P3.2脚外部中断子程序，也就是解码程序 IR: MOV R6,#9 SB: ACALL DELAY882 调用882微秒延时子程序 JB P2.2,EXIT 延时882微秒后判断P3.2脚是否出现高电平如果有就退出解码程序 DJNZ R6, SB 重复10次，目的是检测在8820微秒内如果出现高电-infrared remote control receiver ORG 0000H LJMP START into main program ORG 0010H START : MAIN : JNB P2.2, IR LJMP MAIN below to enter P3.2 foot external interrupt subroutine, which is decoding procedures IR : MOV R6, SB# 9 : Calling ACALL DELAY882 882 microsecond delay subroutine JB P2.2, EXIT 882 microsecond delay after the judgment whether there P3.2 feet to I quit if decoding procedures DJNZ R6, SB repeated 10 times, the purpose is to test if within 8,820 microsecond high

动态接口采用各数码管循环轮流显示的方法，当循环显示频率较高时，利用人眼的暂留特性，看不出闪烁显示现象，这种显示需要一个接口完成字形码的输出（字形选择），另一接口完成各数码管的轮流点亮（数位选择）。 -display

MF500非接触式IC卡开发板源程序 -MF500非接触式IC卡开发板源程序