-
读DS18B20的序列号,读进片内RAM里,KEILC环境下用汇编语言编译调试成功...
读DS18B20的序列号,读进片内RAM里,KEILC环境下用汇编语言编译调试成功-DS18B20 Reading the serial number, read into the RAM chip in, KEILC environment using assembly language compiler debugging success
- 2023-03-20 07:35:03下载
- 积分:1
-
选了一部分比较有代表性的汇编实验题目,都是自己亲手调过的,很有参考价值...
选了一部分比较有代表性的汇编实验题目,都是自己亲手调过的,很有参考价值-More representative selection a part of a compilation of experimental subjects, are transferred off his hand, of great reference value to
- 2022-05-30 03:11:39下载
- 积分:1
-
zlg7289的源程序,可以做参考
zlg7289的源程序,可以做参考-zlg7289 source, reference can be done
- 2022-03-21 16:01:09下载
- 积分:1
-
获取内核内存地址的汇编代码。
获取内核内存地址的汇编代码。-access to the kernel memory address compiled code.
- 2023-04-06 19:25:04下载
- 积分:1
-
汇编语言编写的二十一点小游戏程序。可以直接运行
汇编语言编写的二十一点小游戏程序。可以直接运行-Written in assembly language programs blackjack game. Can be directly run
- 2022-02-20 06:17:52下载
- 积分:1
-
c语言编译的计算器
为了方便了解流程,在程序中把计算过程也输出了.而且栈操作的实现部分也是自己实现的.
程序用两个栈,optr寄存运算符,opnd寄存操
c语言编译的计算器
为了方便了解流程,在程序中把计算过程也输出了.而且栈操作的实现部分也是自己实现的.
程序用两个栈,optr寄存运算符,opnd寄存操作数和运算结果.输入的表达式以等号结束,例如:2*(1+2)=
-c language compiler of the calculator in order to facilitate the understanding of flow, in the procedure to calculate the output of the process. but Stack is the realization of part of their realization. procedures with two stacks, optr storage operator, opnd operand storage and computing the results of . enter the expression in order to equate the end of, for example: 2* (1+ 2) =
- 2022-10-25 02:00:03下载
- 积分:1
-
基于DSP的变频调速
DSP2407 实现了变压变频,控制方法是SVPWM-VVVF based on dsp
- 2022-04-28 16:45:21下载
- 积分:1
-
介绍汇编语言,属于教程一类的,想学习对硬件编程的朋友可以下载来看看。直接解压就可,CHM文件。...
介绍汇编语言,属于教程一类的,想学习对硬件编程的朋友可以下载来看看。直接解压就可,CHM文件。-introduction to the compilation of language, belong to a category Guide, want to learn programming for the hardware can be downloaded friends to see. Decompression can be direct, CHM file.
- 2022-01-24 17:42:14下载
- 积分:1
-
,片选接到p1.5
复位端 p1.4
中断端接到 int0
82c250工作在斜率模式下 ,RS 接51k电阻到地。
2,SJA10...
,片选接到p1.5
复位端 p1.4
中断端接到 int0
82c250工作在斜率模式下 ,RS 接51k电阻到地。
2,SJA1000与82C250的接口,逻辑上为SJA1000输出0(显性位),表现为低点平输出给82C250,则82C250输出
差分的低电平。SJA1000输出1(隐性位),表现为高电平或悬空输出给82C250,则82C250输出悬空状态。
3,周立功的中SJA_BCANCONF.ASM中对输出控制寄存器 的TX0的输出 极性的位的定义不对。
还有里面定义有接收错误标志码,不知道何时用。-, The election received a P1.5-chip client p1.4 interrupt reset int0 82c250 client received in the slope mode, RS then 51k resistor to ground. 2, SJA1000 with the 82C250 interface, logic for SJA1000 Output 0 (dominant bit), showing low level output to the 82C250, while the low-level differential output 82C250. SJA1000 Output 1 (recessive), and the performance of the output is high or left vacant to the 82C250, the vacant state 82C250 output. 3, Zhou Ligong in the SJA_BCANCONF.ASM of output control register TX0 output polarity bit the definition of wrong. Inside the definition also has to receive error flag code, I do not know when to use.
- 2022-06-28 07:07:40下载
- 积分:1
-
关于汇编语言一些进制的转换方法
关于汇编语言一些进制的转换方法-language on the compilation of some band Conversion
- 2023-07-23 08:35:03下载
- 积分:1