误码率仿真讲义，在matlab环境中如何进行接收数据的误码率计算...

继续上面一个,TV TUNER VHF 频段表.-continue above a TV tuner VHF band table.

介绍了一种构建在定点DSP上的高速瑞利衰落信道仿真模型。通过应用确知性瑞利过程的理论，使得仅需要较少的低频正弦波分量以及简单的运算即可实现较高精度的信道建模；进而可采用查表法并结合TMS320C6202定点数字信号处理器的高并行性和处理能力构造高速的仿真模型-Construction of a fixed-point DSP in the high-speed Rayleigh fading channel simulation model. Through the application process unascertained Rayleigh theory, only need to make small low-frequency sine wave components and the simple operation can achieve higher accuracy Channel modeling; then use look-up table method and combination TMS320C6202 fixed-point digital signal processor parallel and can handle Construction of the high-speed simulation model

MRCP V2版协议，MRCP2.0主要将RTSP协议修改为SIP协议-MRCP V2 version of the agreement, MRCP2.0 mainly RTSP protocol amending the agreement for the SIP

《Delphi串口及语音传真高级编程》所附带光盘的源程序，网上不多见，可执行程序网上较多- "Delphi String Mouth And Pronunciation Facsimile High-level Programming" supplements the compact disc the source program, on-line not sees, but the executive routine on-line are more

The SL11RIDE is a low cost, high speed Universal Serial Bus RISC based Controller board. It contains a 16-bit RISC processor with built in SL11RIDE ROM to greatly reduce firmware development efforts. Its serial flash EEPROM interface offers low cost storage for USB device configuration and customer product specific functions. New functions can be programmed into the I2C by downloading it from a USB Host PC. This unique architecture provides the ability to upgrade products, in the field, without changing the peripheral hardware.-USB IDE solution

viterbi算法的c实现，已经验证过，可以直接用-c realize viterbi algorithm has been verified, you can directly use

psk技术实现，并有详细的程序，有助于通信软件的开发-psk technology, and the detailed procedures, contribute to the development of communications software

微软亚洲研究院论文：大规模网络中分布的距离估计-papers Microsoft Research Asia : large-scale distribution network from the estimated

基于linux平台用QT编写的串口通信代码，去年我使用Qt编写串口通信程序时，将自己的学习过程写成了教程（Qt编写串口通信程序全程图文讲解），但是由于时间等原因，我只实现了Windows下的串口通信，并没有去做Linux下的。自从教程发布到网上后，就不断有人提出相关的问题，而其中问的最多的就是，怎样在Linux下实现串口通信。因为有计划安排，而且没有开发板，所以一直没能去研究，也就没能给出很好的解决办法。前些天，网友hqwfreefly 用Qt写了一个叫linucom的Linux下串口调试程序，实现了Linux的串口通信。而且，正好现在我有几天假期，所以就和hqwfreefly合作，将linucom更新为Lincom，并且推出了Windows下的Wincom，然后完成了这篇Qt编写串口通信程序的专题教程，也算完成了我的一个心愿。

cypress 68013 iotest