新型投币机：控制两个按摩椅，具有红外遥控，能够设置最低投币个数及时间，...

美国TI公司的protel 元器件库，在应用中需要更新，本人收集了最新的版本共30M，为提高上传速度分六次上传。文件名依次为TI_1到TI_6。希望大家设计电路板时少走弯路这里是第二个TI-2-TI" s U.S. Treasury protel components, need to be updated in the application, I collected a total of up-to-date version of 30M, to improve the upload speed upload six hours. File name followed by TI_1 to TI_6. Hope that the design of circuit board less detours here is the second TI-2

tl2543的AD程序仅供参考--KEIL51！-tl2543 the AD process is for reference only KEIL51!

这是单片机读写CF卡的详细设计，很有用处-SCM CF card reader for the detailed design, useful

通过ＭＣＵ采集数据并上传到ＰＣ，通过串口协议传送-Through the MCU data collection and upload to the PC, through serial transmission agreement

这篇实验报告是关于单片机多路数据采集的，本实验由2大部分组成：1、为用EPOROM构成的心电信号发生器；2、为多路信号的微机采集与显示；第一部分实验主要研究可编程序存储器EPROM的非计算机应用。把存储在EPROM中的数字心电信号读出并通过D/A转换为模拟信号显示在示波器屏幕上。 第二部分实验的目的是研究一个数据采集系统，该系统利用ECD-51型单片机为中心，由D/A芯片等将各种低频信号以及由EPROM产生的模拟人体心电信号变换成离散的数字信号存入微机内存，以待进行数据处理和分析，然后再通过D/A转换将其还原成模拟信号显示在示波器的屏幕上。 -This experimental report on the multi-SCM data acquisition, the experiment by the two major components : 1. EPOROM pose for the use of the ECG signal generator; 2, multi-path signals in the computer acquisition and display; the first major study of experimental programmable EPROM memory in non-computer applications. Stored in the EPROM of ECG read out by D/A conversion of analog signals displayed on the oscilloscope screen on. Part II The purpose of this experiment is to study a data acquisition system, which uses ECD-51 microprocessor as the center, from the D/A chips, and other various low-frequency signal from EPROM and the simulation of human ECG transform into several discrete signal words into computer mem

D12与电脑通过USB单片机通信的程序，开发人员可以参考

延时采用指令延时的方法,通过改变系统时钟,改变延时的长短,用IOA口的低8位接的LED的闪烁显示出来-Delay the use of methods of instruction latency by changing the system clock, changing the length of delay, and low IOA I received 8 of the LED display flashes

这是i Button这种信息纽扣所采用的1线通讯方式的完整源程序。-This is the information i Button Button 1 line used in the complete source code means of communication.

是基于单片机的温度控制程序，用汇编语言实现，同时带有上位机检测-Is based on the single-chip temperature control procedures, using assembly language to achieve, at the same time with PC Detection

编写一个延时1MS子程序根据题目选择是定时还是记数状态，本题选择记数状态。然后根据延时1MS计算出计时器的初值是E0H（高8位）18H（低5位）。最后编写算法，对T0初始化，利用T0的中断TF0调用中断处理程序。-prepared a delay rungs subroutine under the topic chosen is not a time to memorize numbers or state of mind of the few options that state. According to delay timer rungs calculate the initial value is E0H (high 8) 18H (Low 5). Preparation of the final algorithm, the T0 initialization, interrupt the use of T0 TF0 call interrupt handling procedures.