linux驱动开发linux_drive_the_development.rar中文版

ex6_1 ～ ex6_3二项分布的随机数据的产生 ex6_4 ～ ex6_6通用函数计算概率密度函数值 ex6_7 ～ ex6_20常见分布的密度函数 ex6_21 ～ ex6_33随机变量的数字特征 ex6_34 采用periodogram函数来计算功率谱 ex6_35 利用FFT直接法计算上面噪声信号的功率谱 ex6_36 利用间接法重新计算上例中噪声信号的功率谱 ex6_37 采用tfe函数来进行系统的辨识，并与理想结果进行比较 ex6_38 在置信度为0.95的区间上估计有色噪声x的PSD ex6_39 在置信度为0.95的区间上估计两个有色噪声x，y之间的CSD ex6_40 用程序代码来实现Welch方法的功率谱估计 ex6_41 用Welch方法进行PSD估计，并比较当采用不同窗函数时的结果 ex6_42 用Yule-Walker AR法进行PSD估计 ex6_43 用Burg算法计算AR模型的参数 ex6_44 用Burg法PSD估计 ex6_45 比较协方差方法与改进的协方差方法在功率谱估计中的效果 ex6_46 用Multitaper法进行PSD估计 ex6_47 用MUSIC法进行PSD估计 ex6_48 用特征向量法进行PSD估计-ex6_1 ~ ex6_3 binomial distribution of the generated random data ex6_4 ~ ex6_6 generic function value of the probability density function ex6_7 ~ ex6_20 common distribution density function ex6_21 ~ ex6_33 figure characteristics of random variables periodogram function ex6_34 used to calculate the power spectrum ex6_35 direct method using FFT signal above the noise of the power spectrum ex6_36 recalculated

单片机实现键盘输入数码管显示。给sclk8个上升沿就可以控制一个8段数码管了，当移位寄存器满了后，给st一个上升沿，就可以显示数据了-SCM keyboard input digital tube display. To a rising edge sclk8 can control an 8-segment digital tube, and when the shift register is full, after a rising edge to the st, you can display the data of the

这是一个红外遥控键值解码12864液晶显示，适合初学者及工程开发。-This is an infrared remote control decoder 12,864 pairs LCD, for beginners and project development.

8051核的DES源代码 使用C语言写的基于51核的DES原码，变量定义使用汇编。占用了130字节RAM，比我所见到的包括汇编编写的都要快。 -8051 nuclear DES use source code written in C language based on the 51 nuclear DES original code, the use of variable definition compilation. Occupy the 130 byte RAM, than I have seen in the preparation of the compilation must fast.

T6963C的24064的LCD显示程式-T6963 24064 of the program LCD Display

AT89C51 24c02读写程序 -AT89C51 24c02 read and write procedures to read and write AT89C51 24c02 program

以MPS430F149为硬件平台，利用I/O口模拟I2C总线协议，对日精的时钟芯片S35390A_C做了初始化子程序、读时钟子程序、写时间子程序、脉冲为1赫兹输出子程序。-To MPS430F149 for the hardware platform, the use of I/O port simulation I2C bus protocol on-chip clock nissei S35390A_C done initialization subroutine, read subroutine clock, the time to write subroutines, pulse for 1 Hz output subroutine.

用S1实验板 P1口的8个发光管每隔2个右循环点亮 -Experiments with S1 plate P1 mouth every 8 LED 2 right circle lit

汇编串操作的程序-compilation series operating procedures

MCS51汇编语言，加、减、乘、开平方子程序，经实际应用检验，绝无问题-MCS51 assembly language, add, subtract, multiply, square root subroutine, by the practical application of testing, no problem