MagicARM2410 实验箱使用说明书.

免费开源实时RTOS--FreeRTOSV5.0.3源代码-Free open-source real-time RTOS- FreeRTOSV5.0.3 source code

avr 库函数介绍 对于编程的初学者很重要-avr library function to introduce beginners to programming is very important

介绍了基于LPC932 单片机为处理器的电能表的硬件结构和软件流程-Introduction LPC932 microcontroller based energy meter processor hardware structure and software flow

读标准韦根26码的程序，效果不错，只是需要后上电-Reading standard Wiegand 26 yards of the procedure, good results, but needs power

用 AT89C51、LED 数码管、按键、二极管等部分构成，能实现时钟日历的功能：能进行时、分的显示。也具有时钟，定时时间的设定，实现三路开关定时输出等功能。-With AT89C51, LED digital tubes, buttons, diodes and other components, to achieve clock calendar function: to carry out, the sub-display. Also has a clock, timer time setting, the realization of three-way开关定时output functions.

BTF020实验程序-1 btf020开发板自带-Experimental procedures BTF020 development board comes with-1 btf020

这个包中提供了一些有实际应用价值的子程序供参考选用 SUB1----X25045/43 看门狗/存储器与 89C2051接口子程序 源程序/原理图(21K)X25045.EXE SUB2----AT24C02/04/08/16 串行存储器与 89C2051接口子程序 源程序/原理图(22K) AT24C02.EXE SUB3----红外遥控器(熊猫M50462/C54L2)与 89C2051接口子程序 源程序/原理图(21K) M50462.EXE SUB4----DS1302/HT1302 实时时钟与 89C2051接口子程序 源程序/原理图(20K) DS1302.EXE SUB6----AT89C2051与上位机RS232通讯接口子程序 源程序/原理图(25K) RS232.EXE SUB7----VB5.0 与AT89C2051通讯接口子程序 源程序/原理图(22K) VB5.EXE SUB8----单片机间RS485多机通讯子程序 源程序/原理图(24K) RS485.EXE -this package provides a number of practical value to the subroutine for reference use SUB1----X25045/43 watchdog/memory interface with the 89C2051 subroutine source/schematics (21K) X25045.EXE SUB2----AT24C02/04/08/16 serial memory interface with the 89C2051 subroutine source/schematics (22-karat) AT24C02.EXE SUB3-infrared remote control (Panda M50462/C54L2) and 89C2051 Interface subroutine source/schematics (21K) M50462.EXE SUB4---- DS1302/HT1302 real-time clock and 89C2051 Inter

Keil C51，带有EEPROM的读写和按键、菜单及数码管显示与一体的单片机程序，已通过调试-Keil C51, with the read and write EEPROM and buttons, menus and digital display with integrated single-chip process, has passed through debugging

运用AVR单片机的MEGA16L控制NRF24L01射频芯片接收数据的应用-use mega16l to control nrf24l01 to receive data

1.电子琴功能 用实验板上K1~K7作为电子琴的7个按键，每个按键对应一个音符要求当按下其中一个按键，就通过P2.5口输出对应频率信号使蜂鸣器发出特定音符声音。 2.乐曲演奏 若按下K8键，完成自动弹奏“送别”歌曲。 -1. Organ function of the experimental board K1 ~ K7 as the organ of the seven buttons, each button corresponds to a note of which require that when the press of a button, on the adoption of P2.5 port output frequency signal corresponding to a specific note to the buzzer sounds . 2. Music playing, if pressed K8 button to complete the auto-play " Farewell" songs.