汇编课程设计 图形编辑器

8259A实验程序,可以实现中断实验，已经在星眼上运行了，是非常不错的-this is 8259a

基于汇编语言开发设计DAC0832与8051/52的接口电路，其中，一个输出正脉冲，另一个输出负脉冲，可在proteus软件上结合示波器进行仿真模拟，供大家进行基础学习选择使用

带有LCD和数码管的计时器提醒电路，汇编语言-LCD and digital control with a timer to remind the circuit, assembly language

（1） 有一个主持人控制开关和8路抢答按扭，当主持人允许抢答时才能进行抢答操作，并用一个数码管显示抢答选手的号码，同时其他选手不能再抢答。 （2）电路上要加个蜂鸣器的电路，当有选手抢答时蜂鸣器响一下。 （3）要有倒计时功能，开始抢答时开始倒20秒计时，用两个数码管显示，当有人抢答时停止倒计时。 2.2拓展部分 用按键可设置倒计时的时间，范围在5秒到30秒之间。-(1) has a host switch and 8-way control button to answer in, when the moderator allowed to be carried out to answer in time to answer in operation, and use an LED display to answer in the number of players, while other players can no longer answer in his place. (2) the circuit, we should add a buzzer circuit, when there are players when the buzzer rang to answer in about. (3) to have the countdown feature to begin to answer in 20 seconds when you start down time, using two digital tube display, when someone stops to answer in the countdown. 2.2 The expansion of part of the buttons can be set with the countdown time, the range of 5 seconds to 30 seconds.

在电脑上提示用户输入某一天的年月日，接收用户的信息后，然后算出输入的日期是星期几，并在屏幕上输出计算的结果。完成后进行下一次输入。-on the computer prompts the user to input a day date, the receiving user information, then calculate the date of importation of the week, and on the screen output of the calculated results. Upon completion of the next input.

纯汇编语言程序，忘了是哪个国际计算机大赛获奖程序，强烈推荐-pure assembly language, which is forgotten by the international computer contest winners procedures, and strongly recommended

高级取模软件 高级取模软件 高级取模软件 -Senior High Modulus modulus Software Software Software Senior High Modulus High Modulus modulus Software Software Software High Modulus

stdcall C++ 调用汇编理解。让我们知道函数参数入栈及返回的处理。对比fastcall会更清楚。-stdcall C++ compilation of understanding calls. Let us know the function parameters and return stack processing. Contrast fastcall will be clearer.

,片选接到p1.5 复位端 p1.4 中断端接到 int0 82c250工作在斜率模式下 ，RS 接51k电阻到地。 2，SJA1000与82C250的接口，逻辑上为SJA1000输出0（显性位），表现为低点平输出给82C250，则82C250输出 差分的低电平。SJA1000输出1（隐性位），表现为高电平或悬空输出给82C250，则82C250输出悬空状态。 3,周立功的中SJA_BCANCONF.ASM中对输出控制寄存器 的TX0的输出 极性的位的定义不对。 还有里面定义有接收错误标志码，不知道何时用。-, The election received a P1.5-chip client p1.4 interrupt reset int0 82c250 client received in the slope mode, RS then 51k resistor to ground. 2, SJA1000 with the 82C250 interface, logic for SJA1000 Output 0 (dominant bit), showing low level output to the 82C250, while the low-level differential output 82C250. SJA1000 Output 1 (recessive), and the performance of the output is high or left vacant to the 82C250, the vacant state 82C250 output. 3, Zhou Ligong in the SJA_BCANCONF.ASM of output control register TX0 output polarity bit the definition of wrong. Inside the definition also has to receive error flag code, I do not know when to use.

依照个人成绩进行考核,这是程序的主界面，主要包含其他模块的调用等-that is a programe for education