serial simulation program, occupying only a T2 resources

motorola 集成CAN控制器，外加CAN收发器实现的CAN通讯。 1、速度100K 2、解压后为codewarrior的一个工程-motorola integrated CAN controller, plus CAN Transceivers achieve CAN communication. 1, the speed of 100K 2, unpacked for a project codewarrior

路灯监控，能够自动采集路灯实时信息，并自动报警-road lamp control road lamp control road lamp control road lamp control road lamp control

6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1）， K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用 -6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention

avr 单片机 I2C总线设计原代码c程序设计-Single-chip I2C-bus design avr source code c programming

tcpip.rar 是一个51控制8019的程序,我已用于商用.还很稳定,有兴趣的可以看一下,对TCP IP UDP ICMP ARP RARP HTTP均可以实现.-tcpip.rar control is a 8019 51 procedures I have used the business. very stable, which is interested can look at it. TCP UDP ICMP IP ARP RARP HTTP are to be attained.

PWM波程序 可以用来控制电机调速，程序比较简单，这里只用了一个定时器就实现了。因为51单片机没有PWM波的寄存器，所以要自己用软件控制。-PWM waves program can be used to control motor speed, procedure is simple, here only a timer is realized. Because no PWM waves 51-series microcomputer to yourself, so with registers control software.

93C46储存数字,使用8051单片机； ，可以存取数字-93C46 store numbers, the use of 8051 , you can access the digital

192*64显示lcd程序，功能：根据参数x_add,y_add往LCD中写1个字 输入：1： 写到LCD的X、Y坐标；2：数据地址 输出：无-LCD display procedures, functions : the parameters x_add, LCD y_add to write a character input : 1 : LCD wrote the X, Y coordinates; 2 : data output address : None

这是本关于学习KEIL软件使用方法的书，是PDF格式，请确认你安装了该软件才可阅读-This is the KEIL on learning how to use software, is in PDF format, please make sure you install the software before reading

单片机程序源代码 AD转换 串口通讯 定时器配置 端口配置 延时 I2C通讯 UART串口，KEIL开发环境 -Microcontroller program source code to configure the AD converter serial communication port configuration latency timer I2C communications UART serial port, KEIL Development Environment