DVD管理系统

fdtd程序，线馈矩形微带天线的分析文档，其中包括两种模型的建立，有matlab和C++程序。(fdtd program, line fed rectangular microstrip antenna analysis documents, including the establishment of the two models, with matlab and C++ program.)

说明：  在linux下的简单查找的例子，实用信号和槽的简单运用。(failed to translate)

用于最大信噪比准则方向图和功率谱，自己编写，仅供参考(Pattern for maximum signal-to-noise ratio criterion and the power spectrum, write your own, for reference only)

获取复合文档word/doc excel/xls powerpoint/ppt的信息(Get compound document word doc/excel/XLS powerpoint/powerpoint presentation of information)

对电容屏进行触摸按键的编程设计，电容触摸按键程序(Programmatic design of touch button for capacitive screen, capacitive touch button program)

详细讨论了INSAR技术中相位解缠最小二乘方法的算法实现；并提出改进的加权最小二乘算法的实现思路(INSAR techniques are discussed in detail in the method of least squares phase unwrapping algorithm and suggestions for improvement of the weighted least squares algorithm implementation ideas)

stm32f030工程源码，原子风格代码(stm32f030 project source code, atomic style code)

SIFT，即尺度不变特征变换（Scale-invariant feature transform，SIFT），是用于图像处理领域的一种描述。这种描述具有尺度不变性，可在图像中检测出关键点，是一种局部特征描述子。 该方法于 1999 年由 David Lowe 首先发表于计算机视觉国际会议（International Conference on Computer Vision，ICCV），2004 年再次经 David Lowe 整理完善后发表于 International journal of computer vision（IJCV） 。截止 2014 年 8 月，该论文单篇被引次数达 25000 余次。(来自百度)(SIFT, namely Scale-invariant feature transform (SIFT), is a description used in the field of image processing. This description has scale invariance and can detect key points in images. It is a local feature descriptor. This method was first published by David Lowe at the International Conference on Computer Vision (ICCV) in 1999 and published in the International Journal of Computer Vision (IJCV) in 2004 after it was sorted out and perfected by David Lowe again. As of August 2014, more than 25,000 citations have been cited. (From Baidu))

当有人靠近时，人体热释电检测到信号，led会闪烁(When someone approaches, human pyroelectric signals are detected and led flickers)

说明：  硬件资源: 1,DS0(连接在PA8)，DS1(连接在PD2上) 2,串口1(波特率:115200,PA9/PA10连接在板载USB转串口芯片CH340上面) 3,ALIENTEK 2.8/3.5/4.3寸LCD模块(仅支持MCU屏) 4,按键KEY0(PC5)/KEY1(PA15)/KEY_UP(PA0,也称之为WK_UP) 实验现象: 通过按键KEY_UP可以控制定时器AutoReloadTimer_Handle的开启，这个是 周期定时器，一旦开启就会不断的运行，直到按下KEY1将其关闭。按下KEY0 可以打开定时器OneShotTimer_Handle，这是个单次定时器，只会运行一次， 运行周期到了以后就会停止运行，除非按下按键KEY0将其再次开启。(Hardware resources: 1, DS0 (connected to PA8), DS1 (connected to PD2) 2. Serial port 1 (baud rate: 115200, PA9/PA10 connected on board USB to serial chip CH340) 3, ALIENTEK 2.8/3.5/4.3 inch LCD module (only supporting MCU screen) 4. Keyboard KEY0 (PC5)/KEY1 (PA15)/KEY_UP (PA0, also known as WK_UP) Experimental phenomena: The timer AutoReloadTimer_Handle can be turned on by keying KEY_UP. This is The periodic timer will run continuously once it is turned on until KEY1 is pressed to turn it off. Press KEY0 You can turn on the timer OneShotTimer_Handle, which is a single timer and only runs once. The run cycle will stop after that unless KEY0 is pressed to turn it on again.)