基于CAN总线的电梯控制系统，包括主板程序，子板程序和电路原理图...

keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.

1602 液晶显示 电子表程序时 分 秒 使用的是新华龙单片机 100脚 的 -1602 liquid crystal display digital watches every minute procedure using a new single-chip 100-pin of Hualong

Keil uVision3例证代码NOMOD51 This file is part of the C51 Compiler package Copyright (c) 1988-2005 Keil Elektronik GmbH and Keil Software, Inc. Version 8.01-Keil uVision3 example code NOMOD51This file is part of the C51 Compiler package Copyright (c) 1988-2005 Keil Elektronik GmbH and Keil Software, Inc. Version 8.01

单片机上运行俄罗斯方快.在加上protues软件就可以实现纯软件实现仿真-SCM running on the Russian side soon. In addition protues software can be achieved purely Simulation Software

Interface PS/2 key board-Interface PS/2 key board

用于远程抄表系统中的一个现场数据采集模块，精确到小数点后2位，可采集2路单脉冲2路双脉冲，并向上位机提供数据-For remote meter reading system in a field data acquisition module, accurate to two decimal places can capture 2-way single-pulse 2-way dual-pulse, to the host computer to provide data

此程序为单片机89S52液晶显示模块显示程序.具体解释在程序中有.-procedure for SCM 89S52 LCD display module procedures. Explain the procedures are.

DS18B20的管脚定义：1、GND 2、DQ 3、VCC 温度显示用四位，当温度>=100度时，第四位才显示-DS18B20 pin definition: 1, GND 2, DQ 3, VCC temperature display with four, when the temperature

用2051制作的测试1HZ到1M的频率测试C程序 -2051 produced by the test frequency of 1Hz to 1M test C program

学习C51时写的定时器程序,提供给刚学单片机程序的朋友参考-C51 when learning to write timer procedures, available to just school friends Singlechip procedure reference