这是一个用C++编写的软件，包括手机发送消息的一个…

多线程，多接收模式串口类 LsComm ,串口通信源代码!-multi-threaded, multi-mode receiver category LsComm serial, serial communications source code!

手机多串口编程的资料： 多串口协议GSM0710的各种文档以及参考代码。 0. Readme.txt 本文档 1. 710MUX 源代码，微软MUX驱动模板 2. E901Mux 源代码，E901手机实际运行的MUX驱动 3. mux 一款参考源代码 4. 3GPP-0710.doc 3GPP的多串口协议文档 5. GSM0710_Version7.0.0.pdf GSM07.10 协议规范（英文） 6. GSM0710中文版.doc 本人对GSM0710_Version7.0.0.pdf的翻译 7. NXP_MuTa_SyUM.pdf NXP对MUX部分的介绍（Part2 and Part3 ） 8. gsm0710.c 一份参考源代码 9. gsm0710.jpg 协议的简要流程图 10. gsm0710总结.txt 简单的总结 11. request.dat 请求的数据原样 12. request.txt 对请求数据的分析 13. reply.dat 响应的数据原样 14. reply.txt 对响应数据的分析-mux GSM0710 doc and source code.

高级网络通信编程实串口通信编程实例网络流量监控网站下载网络五子棋系统语音聊天远程监控赠送实例类似网络蚂蚁的断点续传程序网络多播程序界面美观的文字聊天程序语音电话-senior network communications programming is programming examples of serial communications network traffic monitoring website network voice chat system Gobang RMON presented examples of similar networks ants HTTP procedures multicast network interface procedures to the letter beautiful voice chat program

串口程序，使用vc编写，好东西，大家可以分享一下。-Serial procedures, the use of vc preparation, good things, we can share.

串行接口通讯试验该试验可以学习如何编写一个通讯程序。这个试验能够实现的功能很简单，仅仅作为试验用。工作环境为：无需其余任何环境，直接接通电源即可。-serial communication interface test of the pilot can learn how to prepare a communication process. The pilot function can be achieved is very simple, just to experiment with. The working environment : the environment without any rest, can be directly connected to power.

采用C语言,软件模拟硬件UART端口,基于PIC系列处理器实现.-Using C language software simulation of hardware UART ports, based on the PIC family of processors to achieve.

check if COmPort is Available

这是恒坚电器提供的完整的c++串口编程源代码-Tsunekata appliances provide a complete c serial programming source code

实现函数发生器产生的波形能够在电脑显示器上显示。函数发生器通过GPIB卡与电脑连接并传输数据，电脑上通过LABVIEW软件环境完成与GPIB卡的数据通信。在LABVIEW环境下完成了对虚拟仪器前面板以及后台程序框图的设计与编程。在LABVIEW开发环境下，实现对GPIB控制时，采用VISA模块驱动的方法进行编程。设计结果在LABVIEW环境下的虚拟示波器能够实现示波器的功能，能够显示函数发生器所产生的任意波形。- achieve the waveform can be displayed on the screen of the computer which send out by the function generator. The function generator connect to computer through a GPIB card and transfer data. Labview can be communicated with GPIB card and save data on computer. The virtual instrument front panel design and background process diagram programming can achieved under Labview software environment. The realization of GPIB control, using VISA module-driven approach to program in Labview. The result of the design is that the virtual oscilloscope is able to complete the Real oscilloscope function in Labview.

最初学习写单片机串口通讯时的源程序，可以让初学者参考一下！-first learn microcontroller serial communications at the source, so that beginners can take a look!