基于ISD4004 的录音系统。该设计通过对ISD4004 语音芯片的介绍,使读者熟悉了1SD4004 的基本应用。同时给出了单片机控制下的硬件电路和软件设计,...

test ili9320 for keil c

单片机实验，实现双字节无符号数的加法，利用查表指令，在此基础上可以学习查表指令的用法-SCM experiment, to achieve double-byte unsigned number of addition, using look-up table instructions, on this basis, can learn the usage of table look-up instruction

基于51单片机的简易函数发生器的源代码，有需要的可以参考一下-A simple microcontroller based function generator 51, the source code

使用NI M系列采集卡产品的DIO数字通道模拟I2C时序，读写EEPROM LABVIEW实例（原创），采用LABVIEW8.5编程。-Use NI M Series DAQ card products DIO digital channel simulate I2C timing, read and write EEPROM device(original code), using LABVIEW8.5 programming.

压力传感器程序 包括UART GPRS SMS PCF8563-Press Sensor Code based at MSP430

基于51系列单片机内部定时器写的一个时钟程序-51 Series single-chip based on an internal timer to write a clock procedures

Electronics Design Checklist C) 2003 Hank Wallace This a checklist for electronics designers. The idea is for engineers and technicians to share experiences and create a detailed checklist, which the individual designer can pare down to meet his or her specific needs. There are many details that go into the making of a first-run design success, and this checklist helps prevent Murphy s gremlins from marring an otherwise healthy design.-Electronics Design Checklist C) 2003 Hank Wallace This is a checklist for electronics designers. The idea is for engineers and technicians to share experiences and create a detailed checklist, which the individual designer can pare down to meet his or her specific needs. There are many details that go into the making of a first-run design success, and this checklist helps prevent Murphy s gremlins from marring an otherwise healthy design.

MCS-51单片机有5个中断源，其中两个是由-INT0、-INT1引脚输入的外部中断源；另外三个是内部中断源即由T0、T1的溢出引起中断和串行口发送完一个字节或接收到一个字节数据引起中断。触发外部中断有两种方式，即下降沿引起中断或低电平引起中断。当编程TCON中的ITi（i=0、1）为1时，则引起触发的方式为边沿触发方式，反之(ITi=0)为低电平触发方式。每个中断源的中断请求能否得到响应要受两级“开关”的控制，即一个总“开关”-MCS-51 single-chip has five interrupt sources, two of which are by-INT0,-INT1 pin input external interrupt source the other three internal interrupt sources from the T0, T1 overflow caused by the disruption and serial port sending or receiving end of a byte to a byte of data caused by interruption. Triggered external interrupt has two modes, namely, falling edge or low-level disruption caused disruption caused. When programming TCON in ITi (i = 0,1) for the 1:00 has been the subject of a way to trigger the way to the edge of the trigger, on the contrary (ITi = 0) for low-level trigger mode. Each interrupt source interrupt request can be subject to levels in response to

PIC16C5X/XX的烧写器制作 适用于JDM等不能烧写的5X芯片-PIC16C5X/XX burning for the production of JDM apply to the other burning 5X not chip

在C51单片机上使用的1602LCD驱动程序，-In the C51 microcontroller used 1602LCD driver,