判断是否是闰年

PView CE from Microsoft Corporation

文本编辑器（A3） 3.3.1设计题目及要求 三， 文本编辑器（10） 要求：（1）编辑文本； （2）保存、打开指定位置的文本文件； （3）具有输入输出界面。-A text editor (A3) 3.3.1 Design and requirements of Title III, a text editor (10) requires: (1) Edit the text (2) to preserve, open the text file specified location (3) with input and output interfaces.

k分布的杂波的生成 运用于杂波模拟当中-k model clutter mulitisim

有n个整数，使其前面各数顺序向后移m个位置，最后m个数变成最前面的m个数 -There is a whole number n, the number of its previous order of the backward shift position m, and finally the number m of m into the top of the number of

电子钟的源码，是正确的，可以试试哦！应用于微机原理及接口。-Electronic clock source is correct, try Oh! Microcomputer Principle and Interface applies.

基于 ASP 的在线酒店预订酒店管理 客户管理 报表生成

万年历程序 从1302中读出的数据放在67H（高两位年）66H（低两位年）65H(月）64H（星期）63H（日） 62H(小时)61H（分钟）60H(秒)57H(农历月)56H（农历日） 显示缓冲单元7CH-7BH(4CH-4BH)(年低位),7AH-79H(4AH-49H)月,78H(48H)星期, 77H-76H(47H-46H)日,75H-74H(45H-44H)小时,73H-72H(43H-42H)分钟,71H-70H(41H-40H)秒 5EH-5DH(55H-54H)农历年，5CH-5BH(53H-52H)农历月,5AH-59H(51H-50H)农历日 闰月标志为F0,定时器T1为调整时候闪烁用。 1302在设置调整时间后，要改为禁止写入状态，否则在上电复位的时候就发生误写入，使时间值加1分钟 次程序中的段码表只适用于该特殊的硬件，具体的段码表由具体的硬件决定 -Calendar program read from the 1302 data on the 67H (two-year high) 66H (two-year low) 65H (month) 64H (Week) 63H (date) 62H (hours) 61H (minutes) 60H (second) 57H (Lunar Month) 56H (Lunar date) shows a buffer unit 7CH-7BH (4CH-4BH) (year low), 7AH-79H (4AH-49H) month, 78H (48H) Week, 77H-76H (47H-46H) Day , 75H-74H (45H-44H) hours, 73H-72H (43H-42H) minutes, 71H-70H (41H-40H) second 5EH-5DH (55H-54H) Lunar New Year, 5CH-5BH (53H-52H) Lunar month, 5AH-59H (51H-50H) Lunar Leap Day logo for F0, adjust the timer T1 is used when flashing. 1302 adjust at set time, the status should be cha

6221mada.asm.........遥控电机程序， 按遥控器0-9步进电机正转0-9步，按遥控器11-19步进电器分别反转 dianji.asm..........步进电机正转，反转各3圈 keyd.asm............步进电机控制程序p3.2正转,p3.3反转,p3.4停止 步进电机接p1.0p1.1p1.2p1.3 abdian.asm...........步进电机正反快慢转！ madatest.asb.............步进电机测试，最简单的转圈程序 -6221mada.asm ......... electric remote control procedures, in accordance with the remote control stepper motors 0-9 to 0-9 are step-by-step, 11-19 step by remote control electrical inversion, respectively dianji.asm ... stepper motor is ....... turn, reversal of the 3 lap keyd.asm ............ stepper motor control program to p3.2 is, p3.3 inversion, p3.4 stepper motor to stop p1.0p1.1p1.2p1.3 abdian.asm ........... then stepping motor speed to the pros and cons! stepper motor test madatest.asb ............., the simplest circular motion the procedures

MCS51基本调试程序 包括8255、键盘、LED等-MCS51 basic debugging procedures, including 8255, keyboards, LED, etc.

记事本，汇编ASM的-notebook, a compilation of the ASM