一个利用中断修改后进行的A/D采集功能的使用软件.

ADS 1.2 开发的用来烧写 AMD Flash 程序源码-ADS 1.2 use for program AMD Flash

采用Cypress EZ-USB设计原理图

arm3000实验ucosii的移植实验-arm3000 experimental ucosii transplant experiment

单片机实现软件滤波,通过编程,比硬件灵活.-Single-chip filtering software, by programming flexibility than hardware.

LCD 仿真器 一、概述 LCD仿真器是一种电子产品的辅助开发工具。目前LCD（液晶屏）在各种电子产品的使用越来越广泛，开发人员在开发带LCD的产品时会用到各种各样的LCD，这些LCD或是现有的，或是定制，现有的LCD不一定能完全满足设计需要，定制LCD需要时间，需要资金，做好后还有修改的可能性，造成不必要的浪费。传统的做法是用LED（发光管）＋驱动电路来仿真LCD，其弊端有四，一、电路复杂，功耗大，100多点的LCD电流将达1A左右。二、图案逼真性差，不直观。三、制作、修改困难，灵活性差。四、通用性不强。 LCD仿真器完全克服了以上存在的问题，她采用软硬件结合的方法，充分发挥软件在作图、运算方面的优势，使仿真的图案与目标LCD图案完全一致，仿真LCD特性与目标LCD特性几乎一样，并提供强大的LCD图形编辑工具，对于不同的LCD产品，LCD仿真器硬件不必更换，只需制作不同的LCD图案，她的灵活性、通用性将是您开发LCD产品的理想选择。 二、LCD仿真器简介 LCD仿真器由接口硬件、仿真软件和LCD图形编辑软件组成，硬件通过打印口或串口（可设置）与PC机通信，仿真软件和LCD图形编辑软件均在WINDOWS下运行于同一台PC机上.--LCD simulator. You don t need to change hardware, and only produce different LCD pictures. It includes hardware connector, simulation software and LCD graph editor, which could be run under Windows enviroment.

开发协议下载-摄像头协议 TWAIN Specification Version 1.9 This document has been ratified by the TWAIN Working Group Committee as of January 20, 2-development agreement download-camera agreement TWAIN Specification Version 1.9 This document has been ratified by the TWAIN Working Group Committee as of The 20, 2

用C++开发的qt媒体播放器，使用了mpg插件-C++, developed in qt media player, use the mpg plug-in

本文为采用VHDL编写的程序及报告。步骤如下：1设计三位二进制计数器程序 二:设计一驱动循环显示7位数字 2编写LED控制程序如下： 3设计采用原理图方式如下: -VHDL paper prepared for the introduction of procedures and reports. Steps are as follows : Design of a binary counter three two procedures : Design of a drive cycle show seven figures prepared two LED control procedures are as follows : three designs diagram as follows :

可编程片上系统设计技术,目前是一个热点话题，技术含量高，起点也高，所以本文能对大伙儿有帮助。 - On the programmable piece the system design technology, at present is a hot spot topic, the technical content high, the beginning is also high, therefore this article can have the help to everybody.

DSP2812 SPWM项目