在ccs编程环境下，编写了永磁电机SVPWM的控制程序。对dsp的学习很有帮助。...

Atmel算法(pid)-步进电机驱动源码 ,不好用你找我,绝对ok! -Atmel algorithm (pid)- stepper motor driver source code, not with you to find me, is absolutely ok!

一些LCD库 分享给大家了 哈哈~-LCD library share some of the U.S. ha ha ~

6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1）， K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用 -6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention

SST89E58RD仿真器的制作有关的PCB,说明和监控程序,可以用来对51单片机进行仿真-SST89E58RD simulator produced the PCB, description and control procedures can be used for 51 single-chip simulation

这里有武汉恒科 51 单片机仿真器附带的约 80 个 ASM 示例代码,初学 51 单片机汇编的可以有各种示例.-There, Wuhan Hengke 51 MCU emulator with about 80 ASM sample code, beginner 51 microcontroller There are various examples that can be compiled.

支持键盘双击事件的C程序设计,51实例，验证过的-Double-click the event to support the keyboard C-program design a

Proteus中12864LCD驱动实例原理图和源程序。-Proteus were driven 12864LCD example diagram and the source.

MSP 430 计算机USB接口之间的通讯代码-MSP 430 computer communication between the USB interface code

数据采集系统作为沟通模拟域与数字域的必不可少的桥梁有着非常重要的作用。本文介绍的重点是数据采集系统。数据采集与通信控制采用了模块化的设计，数据采集与通信控制采用了单片机8051来实现，硬件部分是以单片机为核心，还包括模-数转换模块，显示模块，和串行接口部分，还有一些简单的外围电路。8路被测电压通过通用ADC0809模-数转换，实现对采集到的数据进行模拟量到数字量的转换，由单片机对数据进行处理，用LCD显示模块来显示所采集的结果，并将数据通过串行口传输到PC机上，MCU与 PC机间的电平匹配采用MAX232接口芯片，由PC机完成数据接收和显示，VB程序编写了更加人性化的人机交互界面。-Data Acquisition System Analog domain as communication with the figure of the indispensable bridge between the domain has a very important role. This article focuses on the introduction of data acquisition system. Control data acquisition and communication of the use of a modular design, data collection and communications control to the use of a 8051 single-chip implementation, the hardware part of the single-chip microcomputer as the core, but also mold- digital conversion module, display module, and serial interface part, have some simple external circuit. 8 road test voltage through the common mode ADC0809- conversion, implementation of the collected data to the digital analog conversion, the

为Visual borland c builder实现Vision2 DLL