汇编语言程序设计自学设计教程

此程式为LED驱动,用合泰的蕊片,希望对大家有帮助-This program for LED-driven, with the chips Hetai hope everyone has to help

从首地址为1000H开始存放10个数，要求设计程序将这些数由小到大排序，排序后的数仍放在原地址处。-Starting from the first address 1000H store the number 10 to require the design process to sort these the number of small to large, sort after a few still on the original address.

JAVA课本原代码 有关图象编辑等其他编程内容-textbooks Java code on the original image editing and other programming content

基于DS18B20温度传感器的设计程序 要求为：第一，由DS18B20获得外部温度信息然后通过数码管显示，显示值为三位，两位整数，一位小数。第二，判断温度是否大于 50℃，若温度在50℃以上，显示红色发光二极管发光；若温度在50℃以下，显示绿色发光二极管发光。-DS18B20 temperature sensor based on the design of procedural requirements: first, by DS18B20 access to external temperature information through a digital display, showing a value of 3, two integer, a decimal. Second, to determine whether the temperature is greater than 50 ℃, if the temperature at 50 ℃, which indicates that the red light-emitting light-emitting diodes if the temperature below 50 ℃, showing a green light-emitting diode LED.

拥有众多汇编案例,案例26钟表显示,案例4加减乘除四则运算　,案例9音乐演奏, 案例23学生成绩管理-Has many collection of case studies, case 26 watch display, case-4 addition and subtraction multiplication and division four operations, case 9, music, Case management of 23 student achievement

Input 8 bit binary number and print out its decimal equivalent.

ST套件产生汽车防盗器报警声,本实例的目的是让大家学会用单片机产生声音的方法，学会计算程序所用时间 本实例的功能是能用16F84产生汽车防盗器的报警声，频率分两个0.1s第一个 0.1S频率从1.8K-3.5K匀速增加第二个0.1S频率从3.5K-1.8K匀速减少, 程序复位后,按S2喇叭叫两声,按S3喇叭叫15秒,中途可按S5停止. PIC单片机 烧写时应注意：配置位已经在程序中写明，加载HEX文件时会自动加载，烧写时不用再手动设置配置位。 实验时请注意套件跳线选择；-pic

频率计(51单片机开发例子子程序汇编语言编写)-Frequency meter (51 single-chip development to prepare examples of assembly language subroutines)

基于51单片机的带时间显示和紧急控制的交通灯的设计。 此程序在硬件上调试通，用定时器1延时，外部中断0接紧急控制，R0为100MS延时常数，R2为状态延时常数，8279控制数码管显示时间,用P1口控制双色灯-With 51 single-chip based on the time display and the emergency control of traffic lights design. On this process in hardware debugging pass, with one delay timer, external interrupt 0 then the emergency control, R0 for 100MS constant delay, R2 for a state of constant delay, digital 8279 control display time control using two-color lights I P1

该课程设计使用了三块接口芯片，8253、8255、8259；在程序中需要对8255芯片的控制口进行修改，改成自己所用实验板的端口-The course is designed to use the three interface chip, 8253,8255,8259 in the program need to control the port 8255 to modify the chip, into his own experimental port board