霓虹灯渐变控制器 适合用于装饰 采用单片机实现

单片机系统上电后，P0 口和 P1 口都被清 0。然后，你规定一个由 6 个数字构成的序列（每个数字从 0～F 中选取），比如 E、8、9、0、7、F。然后每次当单片机检测到外部中断 0发起中断时间时，读取 P0 口和 P1 口上的状态值，当连续 6 次外部中断事件的对应的数字序列构成你所设定的序列后（举例来说，如果 P0.0 是 1，P0 和 P1 的其他管脚是 0，那么我们称为检测到一次数字 0），从串口打印输出一幅类似下图的 16×16 的ASCII码的圣诞树图片。-Single-chip microcomputer system after power, P0 and P1 mouth I have been ching 0. Then you set a six figure constituted by the sequence (each number from 0 ~ F in selected), for example, E, 8,9,0,7, F. And then each time a single-chip detects external interrupt 0 initiated interruption time, I read the P0 and P1 mouth on the state value, when a row 6 times the corresponding external interrupt events constitute digital sequence set your sequence (for example example, if P0.0 is 1, P0 and P1 of the other pin is 0, then we called a number of detected 0), a printout from the serial port under similar 16 × 16 map of the ASCII code of the Christmas tree图片.

用C语言写的PS2代码，有比较好的通用性，并且在实际项目中用过-Using C language to write code of PS2, has a relatively good general, and used in actual projects

本设计以凌阳16位单片机SPCE061A为核心控制器件，配合Xilinx Virtex-II FPGA及Xilinx公司提供的硬件DSP高级设计工具System Generator，制作完成本数字式外差频谱分析仪。前端利用高性能A/D对被测信号进行采集，利用FPGA高速、并行的处理特点，在FPGA内部完成数字混频，数字滤波等DSP算法。-The design SPCE061A Sunplus 16-bit single-chip microcomputer as the core control device, coupled with Xilinx Virtex-II FPGA and Xilinx provide hardware DSP design tools Advanced System Generator, the production of the completion of this digital heterodyne spectrum analyzer. Front-end use of high-performance A/D acquisition of the measured signals, the use of FPGA high-speed, parallel processing characteristics, in the completion of the digital mixer internal FPGA, digital filtering and other DSP algorithms.

蓝牙耳机的参考电路图，便于开发蓝牙耳机人供参考-Bluetooth headset reference circuit to facilitate the development of Bluetooth headset, for information,

关于CY68013 USB2.0批量速度的测试程序,感兴趣的可以下载看看.-CY68013 USB2.0 speed on the bulk of the test procedure, interested can download and see.

也许你在网上找个半天也找不到详细介绍CAN 协议的文档,不要找了,我这个就是很详细介绍CAN 协议的文档,协议明白了,再在各个平台调试程序就方便多了.-Maybe you can not find on the Internet to find a half-day details of CAN protocol document, not to find, I introduced the CAN protocol is a very detailed document, the agreement to understand, and then in various Platform Debugger program more convenient.

ICD 2.5(18F4550+16F877)最全的资料！-ICD 2.5 (18F4550 16F877) the most complete information!

本设计以P89V51RD2FN单片机为电动小车的控制核心，采用MSA-LD2.0倾角传感器实时测量跷跷板的倾斜角，用ST198光电传感器检测黑色引导线监测小车运动。光电传感器和倾角传感器模块把实时测量信号馈送至单片机，利用专用细分芯片TA8435H驱动步进电机，以脉宽调制式斩波方式对步进电机步进角进行细分，控制和调节小车速度。采用增量式PID控制算法确保小车能够达到平衡；用RT128×64M液晶显示时间、角度等参数。经测试表明：小车各项性能指标达到设计要求，能够实现30秒内小车行驶到规定点，并保持跷跷板平衡；在跷跷板一端配重可调整的情况下，小车也能自动找到平衡点并保持跷跷板平衡。-The single-chip design for the electric car P89V51RD2FN control of the core, the MSA-LD2.0 seesaw angle sensor real-time measurement of the tilt angle, the detection of black ST198 photoelectric sensor to monitor vehicle movement and guide lines.Photoelectric sensors and angle sensors in real-time measurement module to feed the signal to the microcontroller, using a dedicated sub-chip stepper motor driver TA8435H to PWM chopper-type stepper motor on the sub-stepping angle, control and regulation vehicle speed. The use of incremental PID control algorithm to ensure that the car can achieve balance with LCD RT128 × 64M time, angle and other parameters.After the test showed that: the performance car

电机驱动电路 提供了H桥电路设计的几点思路和PWM的实现方法以。-Motor drive circuit provides the H bridge circuit design ideas and ways to realize the PWM.

利用89C2051实现模数转换的一种方法源程序，该程序使用C51语言编写，可以用于MCS8051单片机-use 89C2051 analog-digital conversion of a way to the source, the procedure used to prepare C51, SCM can be used Mcs8051