-
W3100是WIZnet公司专门为以太网互联和嵌入式设备推出的硬件TCP/IP协议栈芯片,其硬件TCP/IP协议栈包含了TCP、UDP、IP、ARP和ICMP协...
W3100是WIZnet公司专门为以太网互联和嵌入式设备推出的硬件TCP/IP协议栈芯片,其硬件TCP/IP协议栈包含了TCP、UDP、IP、ARP和ICMP协议,这是他的indirect模式的原码-WIZnet W3100 is designed for the Internet and Embedded Ethernet equipment introduced hardware TCP/IP protocol stack chips, and hardware TCP/IP protocol stack includes TCP, UDP, IP, ICMP and ARP agreement, it is his indirect model of the original code
- 2022-08-09 10:14:34下载
- 积分:1
-
Sunplus SCM voice two procedures for learning Sunplus SCM reference learners
凌阳单片机的语音程序2,供学习凌阳单片机的学习者参考-Sunplus SCM voice two procedures for learning Sunplus SCM reference learners
- 2023-09-03 15:55:03下载
- 积分:1
-
SCM and temperature sensor applications, a lot of wrong. Can be used as the basi...
单片机和温度传感器的应用,错误很多。可作为无线应用的基础。请踊跃下载啊。
- 2022-01-30 17:12:21下载
- 积分:1
-
dds a detailed description of control characters, beginners learn to be helpful.
dds控制字的详细描述,对新手入门有帮助。-dds a detailed description of control characters, beginners learn to be helpful.
- 2022-08-14 03:22:48下载
- 积分:1
-
C write I2C EEPROM read and write procedures, the AT24C64 MSP430+ ~ 512 platform...
用C写的I2C总线EEPROM读写程序,在MSP430+AT24C64~512平台上验证通过。对其他处理器只需简单修改即可使用。-C write I2C EEPROM read and write procedures, the AT24C64 MSP430+ ~ 512 platform validation through. The only other processor can use a simple amendment.
- 2022-04-24 05:12:36下载
- 积分:1
-
LCD12864 Driven Development in KeilC51 very useful
LCD12864驱动开发,在KeilC51中非常有用
- 2022-03-23 07:12:49下载
- 积分:1
-
热电偶测温误差分析 论文
针对工业加热炉,详细分析了热电偶测温过程。由于热电偶热端与炉墙内表面之间的辐射换热,以
及热电偶本身因热端和冷端温度不同造成...
热电偶测温误差分析 论文
针对工业加热炉,详细分析了热电偶测温过程。由于热电偶热端与炉墙内表面之间的辐射换热,以
及热电偶本身因热端和冷端温度不同造成的导热总是存在,因此热电偶测温存在误差。本文从理论上分析了
热电偶测温误差的来源,提出了热电偶测温误差计算模型,并导出了测温误差的近似计算公式,还结合实例讨
论了减小测温误差的措施。
- 2022-02-16 06:23:52下载
- 积分:1
-
ICCavr编写的TWI总线协议读写函数,测试通过
ICCavr编写的TWI总线协议读写函数,测试通过-ICCavr prepared by TWI bus protocol to read and write function, the test
- 2022-04-20 15:42:20下载
- 积分:1
-
keilc+ proteus light parallel port design of experiments requirements: master th...
keilc + proteus
并行口设计指示灯实验
要求:掌握80C51单片机输入输出接口使用方法
学会开关量输入输出控制的接口技术及编程方法
实验题目:8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上,一个开关接在P3.0上。要求输出端口输出 “0”时,发光二极管亮。开关闭合时,开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED,再按 P1.7-P1.6 -...-P1.0的顺序点亮LED,重复循环。开关断开时,立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.
- 2022-11-16 18:10:03下载
- 积分:1
-
C8051
c8051-nrf2401 测试程序 发送部分-NRF2401_receive2 c8051f330
- 2022-03-20 13:24:59下载
- 积分:1