对51单片机的介绍，是菜鸟级入门的好资料，能让学生更好的学习...

这是ch375与单片机51接口应用程序，用keil51编译器打开即可-ch375 interface with the MCU 51 applications, with keil51 compiler can be opened

单片机用T1中断在IO口P1.0输出乐曲(在P1.0口与VCC间接一喇叭即可听到) 1.由于输出的是方波，比较难听:-)你也可以将波形细分用DA输出正弦波 2.由于T1频繁中断，任何其他中断发生都会是乐曲打顿，只适合试验 3.优化音符编码：一个字节中包含节拍、音符、升降调，可区分数据和命令 -Single-chip microcomputer used in the IO port T1 interrupt output music P1.0 (P1.0 port with VCC in the indirect one can hear the speaker) 1. As the output is a square wave, more bluntly :-) You can also fine-waveform DA output sine wave with sub-2. Due to the frequent interruption of T1, any other interruption occurs Dayton will be playing music, is only suitable for test 3. optimized coding notes: A byte contains rhythms, notes, take-off and landing tune can distinguish between data and command

摩托罗拉单片机的串行通信中断方式的原代码-Motorola MCU serial communication interrupt the original code

用于储存大量数据，它有一个定时器，到一定数量，它会自动报警。-used to store large amounts of data, it has a timer, to a certain number, it will automatically alarm.

FIQ有FIQ_PWM、FIQ_TMA和FIQ_TMB三个中断源,当定时器A或B计满溢出时产生中断请求信号TA_TIMEOUT_INT或TA_TIMEOUT_INT,CPU响应后进入中断执行相应的子程序控制二极管发光。A口的低四位接LED灯，B口的低四位接LED灯.-FIQ has FIQ_PWM, FIQ_TMA and FIQ_TMB three interrupt sources, when the timer A or B when the expiration overflow interrupt request signal TA_TIMEOUT_INT or TA_TIMEOUT_INT, CPU response after interruption of the implementation of the corresponding subprogram control light-emitting diodes. A low population of four LED lights then, B I take the low four LED lights.

MSP430系列16位超低功耗单片机实践 -MSP430系列16位超低功耗单片机MSP430系列16位超低功耗单片机

单片机操作EEPROM 240X的程序。 非原创，转载。-EEPROM 240X MCU operating procedures. Non-original and reproduced.

基于盛群单片机开发的 获得温湿传感器dht11和光敏电阻的数据 并且发送到1602显示屏的程序-Holtek-based single-chip temperature sensor was developed and photosensitive resistance dht11 and sent to the data display process 1602

Xilinx_Spartan3E开发板的常见疑难问题解答-Development board Xilinx_Spartan3E Common Troubleshooting

1． 电梯初始位置在第一层。 2． 算法完全模拟电梯工作。 3． 显示电梯所在层数和运动方向。 4． 按键复用，部分按钮在不同的时候表示两种功能。 -1. Elevator initial position in the first layer. 2. Algorithm fully simulated elevator work. 3. Show where the low-rise elevator direction and movement. 4. Key reuse, and some buttons at different times, said two functions.