their practice of the small things, the 8031 NE2000 compatible Ethernet control...

ARM I2C 通讯软件(中断方式）,通过此程序，可以方便的完成CPU 和其他芯片之间的I2C通讯。-I2C communication with ARM (INT mode)，by it, could do communication between CPU and other chip.

AT24C256是ATMEL公司256kbit串行电可擦的可编程只读存储器，8引脚双排直插式封装，具有结构紧凑、存储容量大等特点，可以在2线总线上并接4片该IC，特别适用于具有高容量数据储存要求的数据采集系统。本文将介绍该IC的工作原理和与单片机的软硬件接口。-ATMEL Corporation AT24C256 is 256kbit serial electrical erasable programmable read-only memory, 8-pin double-line package, has a compact structure, characterized by large storage capacity can be 2-wire bus, and then 4 the IC, is especially suitable for high-capacity data storage requirements of the Data Acquisition System. This article will introduce the working principle of the IC and single-chip hardware and software interface.

电机驱动！四相五线的步进电机用C8051F020驱动-Motor drive!

基于单片机的USB设计方案，该方案包括了电路原理图、PCB布局图、单片机端的源程序和PC端的USB调试助手，该方案内容详尽。-USB single-chip design based on the Program, which includes the circuit schematic, PCB layout, Microcontroller and PC client-side source code of the USB debugging aides, the program detailed.

单片机开发源代码集锦 31例 需要的话请去下载-Single-chip development allehanda 31 cases the source code necessary to download please

DSP2812 控制CY7C68001的源码,有详细的注释-DSP2812 control CY7C68001 source, there are detailed notes

自动交通管理系统 用红、绿、黄三支共两组发光二极管表示交通信号灯，利用单片机模拟有时间显示的定时交通信号灯控制管理。信号灯的变化规律可如下： 1）放行线：绿灯亮放行25秒，黄灯亮警告5秒，然后红灯亮禁止。 2）禁止线：红灯亮禁止30秒，然后绿灯亮放行。 3）当某一方向的红灯亮时，若该方向有车通过，则用扬声器声报警。（撞红灯信号可用3-5V模拟量表示） 同时用2位数码管进行30秒钟递减时间显示。-automatic traffic management system using red, green, yellow a total of three light-emitting diodes, said two traffic lights, using SCM time simulation shows the regular traffic signal control. Signal changes in the law to be as follows : 1) Release Line : green clearance 25 seconds, bright yellow warning five seconds, and then the red-ban. 2) prohibit the lines : red-Ban 30 seconds, then green clearance. 3) When the red light in one direction- that if the direction of a car passed, the use of loudspeakers sound alarm. (Red light signals can hit 3- 5V analog said), while using two digital tube for 30 seconds decreasing time displayed.

LCD模块 能够在按下一个键后 在液晶上显示相应的数据 -LCD module can press a button and the LCD display on the corresponding data

c51语言入门教程.适合于初学者使用,通俗易懂-C51 Language Tutorial. suitable for beginners to use, easy to understand

C8051F06X单片机编程，UART模块代码-C8051F06X Microcontroller Programmer, UART module code