51 PDIUSBD12 source code

用AVR编写的24小时时钟程序，还望采纳-AVR prepared with a 24-hour clock procedures, but also look to adopt

x25045的编程应用，它具有512字节的EPROM，看门狗，复位信号等，是MCU不错的外围芯片-x25045 programming application, which has 512 bytes of EPROM, watchdog, reset signal, MCU is a good peripheral chips

c51文件系统源码-decoder source file system

FREESCALE MCF52XX eTPU控制三相电机的程序-eTPU CODE

这是在用MSP430写的LCD12864和温度传感器18B20的驱动程序。-This is written with MSP430 and temperature sensors LCD12864 driver 18B20.

AVR单片机入门及C语言高效设计实践（五） ATMEAG16L的中断系统什么是“中断”？顾名思义中断就是中断某一工作过程去处理一些与本工作过程无关或间接相关或临时发生的事件，处理完后，则继续原工作过程。比如：你在看书，电话响了，你在书上做个记号后去接电话，接完后在原记号处继续往下看书。如有多个中断发生，依优先法则，中断还具有嵌套特性。又比如：看书时，电话响了，你在书上做个记号后去接电话，你拿起电话和对方通话，这时门铃响了，你让打电话的对方稍等一下，你去开门，并在门旁与来访者交谈，谈话结束，关好门，回到电话机旁，拿起电话，继续通话，通话完毕，挂上电话，从作记号的地方继续往下看书。由于一个人不可能同时完成多项任务，因此只好采用中断方法，一件一件地做。[第一段] -AVR C language portal and efficient design practice (5) ATMEAG16L the system even interrupted Mody is "suspended"? As the name suggests is interrupted interruption of a process to deal with some of the work process unrelated or indirectly related to the temporary or , after treatment, to the original process. For example : in your reading, the phone rang, you have the book to be a mark after picking up the telephone, then after the original mark to continue down the reading. For more interruption, priority rules and the suspension characteristics also have nested. For instance : reading, the phone rang, you have the book to be a mark after pick

用MSP430F149仿真SPI接口读写FM25系列铁电的测试程序。包括单字节和多字节读写。已通过测试。请大家放心使用。-with MSP430F149 simulation SPI serial interface to read and write 25 ferroelectric testing procedures. Including single-byte and multi-byte read and write. Have passed the tests. Please rest assured use.

1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.

液晶显示器与单片机接口电路程序，实现液晶显示对于信号源发生信号的控制和显示-LCD and microcontroller interface circuit procedures, LCD occurred signal source for the control signal and display

FlashFlex51单片机