-
摘 要 本系统按要求制作了一个简易智能电动车,它能实现的功能是:从起跑线出发,沿引导线到达 B 点。在此期间检测到铺设在白纸下的薄铁片,并同时发出声光指示信...
摘 要 本系统按要求制作了一个简易智能电动车,它能实现的功能是:从起跑线出发,沿引导线到达 B 点。在此期间检测到铺设在白纸下的薄铁片,并同时发出声光指示信息,实时存储、显示在“直道区”检测到的薄铁片数目。电动车到达 B 点以后进入“弯道区”,沿圆弧引导线到达 C 点,能够检测 C 点下正方形薄铁片,并在 C 点处停车 5 秒,停车期间发出断续的声光信息。之后继续行驶,在光源的引导下,利用超声传感器传来的信号通过障碍区进入停车区并到达车库。最后,电动车完成上述任务后能够立即停车,全程行驶时间小于 90 秒。-abstract:this systme is about making a simple intelligence electroomobile.the main function:star in the scratch line,along the guide line to point B.during this course,it detectes the thin iror sheet under the blank paper, at the same time it gives out voice and light indicaton message, saves the real-time message,and derects and shows the nombers of the thin iror sheet in the straight district. The electromobile goes into curve district when passing poiont B,and runs,along the camber line to point C. The electromobile can detect the square thin iror sheet under the point C, and stop for 5 seconds.During the pause ,it gives out voice and light message sequencly,then it continues to run .Using light inducting and signal of the ultra
- 2022-02-02 19:35:23下载
- 积分:1
-
用C语言实现学生学号,姓名,五门课程成绩的录入与查寻,统计不及格人数,优秀学生人数,平均成绩等。...
用C语言实现学生学号,姓名,五门课程成绩的录入与查寻,统计不及格人数,优秀学生人数,平均成绩等。-C language students learn, names, five courses with the results of the search entry, compared to statistics, the number of outstanding students, the average performance.
- 2022-02-02 22:57:54下载
- 积分:1
-
新的pvpgn bnetd 1.8.5版本
New For Pvpgn 1.8.5 bnetd version
- 2023-05-19 10:25:04下载
- 积分:1
-
user interface programming DialogBar Test
用户界面编程DialogBar的试验-user interface programming DialogBar Test
- 2023-07-15 01:00:03下载
- 积分:1
-
A very nice Flash+ XML image carousel source
很漂亮的Flash+XML图片轮播源码, -A very nice Flash+ XML image carousel source
- 2022-07-19 06:50:36下载
- 积分:1
-
找茬游戏原码,很不错的!
找茬游戏原码,很不错的!-softened the original game code, very good!
- 2022-01-24 16:35:04下载
- 积分:1
-
QT4做的日历,希望能够对需要的人有帮助。
QT4做的日历,希望能够对需要的人有帮助。-QT4 Calendar
- 2022-03-09 12:10:16下载
- 积分:1
-
递归与分治算法的应用.零件切割问题
给定一块宽度为W的矩形板,矩形板的高度不受限制。现需要从板上分别切割出n个高度为hi,宽度为wi的矩形零件。切割的规则...
递归与分治算法的应用.零件切割问题
给定一块宽度为W的矩形板,矩形板的高度不受限制。现需要从板上分别切割出n个高度为hi,宽度为wi的矩形零件。切割的规则是零件的高度方向与矩形板的高度方向保持一致。问如何切割使得所使用的矩形板的高度h最小?
-recursive algorithm with the partition of the application. Parts mutilation given a width of the rectangular plate W, the height of rectangular plate unrestricted. Board is required from the respective cut out n height of the hi, wi width of the rectangular parts. Cutting parts to the rules of the height of the rectangular plate with a high degree of consistent direction. Asked how cutting makes use of the rectangular plate height h minimum?
- 2022-01-26 05:51:05下载
- 积分:1
-
windows下的调色板源代码
windows下的调色板源代码-the palette windows source code
- 2022-02-20 23:30:16下载
- 积分:1
-
大量可供参考的C 语言源程序库
大量可供参考的C 语言源程序库-plenty of reference for C language source
- 2022-03-19 23:55:50下载
- 积分:1