本程序是在c51低下的菜单程序。 如果要mcu 低下编写菜单的朋友可以拿来参考....

为了让广大的工科大学生理解单片机应用系统的开发方法，我们特别提供一个中小规模的典型应用案例，我们把具有详细注释的基于AT89C51单片机的心电信号发生器软件供大家参考，不妥之处请大家批评指出，愿此软件能够给你一点帮助，南昌航空大学自动化学院生物医学工程赵文龙供。2008年8月28日。-In order to enable the broad masses of the engineering students to understand single-chip microcomputer application systems development methodology, we are particularly small and medium-sized to provide a typical application case, we have a detailed annotated AT89C51 single-chip microcomputer-based ECG Signal Generator Software for your reference, not properly requested of the U.S. criticism that this software would like to be able to give you a little help, Nanchang University of Aeronautics automation Zhao Wenlong Institute for Biomedical Engineering. August 28, 2008.

两个点的线性插值定点数算法 说明：1、基本公式 y=( y2-y1 ) ( x-x1 ) / ( x2-x1 ) + y1 2、根据直线斜率的正负、内插外插的不同，分为6种情况。 3.参见文件夹中的“插值算法的6种情况”一图。-two points of linear interpolation algorithm for determining points : one, the basic formula y = (y2- y1) (x-x)/(x2- x1) y1 2, according to the slope of the linear positive and negative, interpolation, extrapolation of different, divided into six kinds of situations. 3. See folder "interpolation algorithm for the six species of" a map.

C8051F04x单片机可变周期PWM脉宽调制。-C8051F04x Singlechip variable pulse width modulation PWM cycle.

mega16 实现的控制舵机的程序，在winavr20080610上编译通过，用户可自己制作makefile函数在winavr上编译使用-realize mega16 steering gear control procedures, in winavr20080610 compiled through, users can produce their own makefile function winavr compiled using

步进电机驱动，简单使用，只需稍加修改，即可用于你想到的系统-Stepper motor-driven, simple to use, just a little modification, you can think of for your system

IIc应用子程序，此程序可应用AT24C08等等串行EEPROM芯片的开发和学习使用，此程序调试通过-IIc application subroutine, this procedure can be applied so AT24C08 serial EEPROM chip development and learning to use, this program debugging through

ds1820的源码驱动-The source driver ds1820

CF卡的驱动编程,含有CF卡驱动的介绍,是入门的好资料.-CF card-driven programming, which contains the introduction CF card driver is a good data entry.

///*** *** *** * //一、程序说明： //1, 24LC02器件地址是1010000R/W. //2, 数组写入24LC02采取页写方式. //3, 数组code从24LC02读出时采取自由读方式. //4, 采用4.00M晶体。 //5，采用软件I2C。 //二、硬件连接： //1， SDA------->23 pin.(当然你可以任意选择脚位） //2, SCL------->18 Pin.(当然你可以任意选择脚位） //3， PORTB----->数码管的段输出 //4， RD4，RD5，RC6，RC7------->数码管的位输出(数码管为共阴极） -///*******************// A description of the procedures:// 1, 24LC02 device address is 1010000R/W.// 2, write an array to take 24LC02 page write mode.// 3, the array read out the code from the 24LC02 to take a free read.// 4, using 4.00M crystal.// 5, using software I2C.// Second, the hardware to connect:// 1, SDA-------> 23 pin. (Of course, you can choose to pin)// 2, SCL-------> 18 Pin. (Of course You can choose pin)// 3, PORTB-----> digital tube output segment// 4, RD4, RD5, RC6, RC7-------> digital pipe-bit output (digital tube for a total of cathode)

c51的实例，学习时做的，看你们有没得用哈-C51 example, learning when to do to see you have not to use Kazakhstan