-
Battery LED light automatic lighting control system design and implementation, w...
光电池LED自动照明控制系统的设计与实现,这是一套毕业设计,里面包括电路原理图和程序原码包,还有相关的芯片资料,这是一套很大的系统
-Battery LED light automatic lighting control system design and implementation, which is a graduation project, which include the circuit schematic diagram and procedures for the original code package, and chip-related information, this is a great system
- 2022-02-04 20:07:59下载
- 积分:1
-
16x16LED 点阵屏源代码和电路图,可以实现上下移,左右移
16x16LED 点阵屏源代码和电路图,可以实现上下移,左右移-Dot-matrix screen 16x16LED source code and schematics can be achieved on the lower left and right shift
- 2023-03-29 20:20:03下载
- 积分:1
-
This is the AD conversion chip AD7705 initialization procedure is the configurat...
这是AD转换芯片AD7705的初始化程序,主要是寄存器的配置-This is the AD conversion chip AD7705 initialization procedure is the configuration register
- 2022-08-18 17:11:17下载
- 积分:1
-
单片机80C522,里面有实用的程序源吗码
单片机80C522,里面有实用的程序源吗码-80C522 microcontroller, there are practical program source code?
- 2022-02-16 04:43:39下载
- 积分:1
-
usbn9603 such as the transmission of the firmware
usbn9603等时传输的firmware-usbn9603 such as the transmission of the firmware
- 2022-03-17 10:37:44下载
- 积分:1
-
, c51 is the classic single
,c51 是经典的单片机,简单,精通51单片机,在学习其他的单片机 很易上手
-, c51 is the classic single-chip, simple, fluent in 51 single-chip, single-chip microcomputer in the learning of other very易上手
- 2022-03-07 10:19:53下载
- 积分:1
-
430的SD16模块扩展到20bit采样精度的范例
430的SD16模块扩展到20bit采样精度的范例-430 extended to the SD16 module 20bit sampling accuracy of the sample
- 2022-01-25 23:27:04下载
- 积分:1
-
八路模拟采集显示电路 可对模拟信号进行采集 并用数码管显示...
八路模拟采集显示电路 可对模拟信号进行采集 并用数码管显示-Eight-way acquisition display circuit simulation can be carried out on the analog signal acquisition and digital display
- 2022-12-20 16:35:03下载
- 积分:1
-
这是一个LED液晶显示的程序...有多个接口..可以用的我用过
这是一个LED液晶显示的程序...有多个接口..可以用的我用过-This is a LED LCD procedures ... .. a number of interface can be used with the I
- 2023-04-28 06:05:03下载
- 积分:1
-
* Hardware architecture: PA0
* 硬件结构: PA0-5对应6个LED数显管的位 ,PC0-7对应各LED数显管的段 ,PB4-7为键盘。
* 软件描述: 上电后,时钟从00.00.00(时/分/秒)自动走时,在走时状态时 , 按PB4(设定
* 键)超过3秒可循环选择调整时间/工作参数 ,接着按PB5以确定选择的操作 ,进入调整操作后 ,
* 按PB5选择欲调整参数,按PB6(增加键)完成调整参数操作 。按PB7,进入时控运行,PB1亮,
* 再按PB7停止时控运行,回显走时。在定时到时,PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard.
* Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis
* The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation
* Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov
- 2022-04-16 19:29:12下载
- 积分:1