MSP430x11x1 Series Single

本程序已经调试通过，使用I2C来从外部时钟芯片中读取并写入时间。文档包含i2c的驱动程序、时钟芯片的读与写、以及使用定时器中断产生脉冲来模拟gps对时。-This procedure has been debugging through the use of I2C chip from the external clock time to read and write. Document contains the i2c driver, the clock read and write chip, and the use of the timer interrupt to simulate the pulse generated when the gps on.

基于时间触发调度器的PID控制，程序所用期间为C515，PID带有抗死锁功能-Time-triggered scheduler based on the PID control, the procedure used for C515, PID with anti-lock function

Electronicworkbench5.1，非常简单的电路分析软件，对电路分析、模拟电路等课程的简单电路进行方针，验证计算结果。-Electronicworkbench5.1

单片机 Keil＋proteus 并行口设计数字键盘实验 要求：掌握动态显示、动态扫描键盘的工作原理及硬、软件的设计、调试方法 掌握80C51接口硬件电路设计方法及软件编程方法 了解80C51外部中断的使用和编程方法 实验题目：并行口实现数字0~9、A~F、L、U、P、n总共20个键盘，将按键的结果用7段数码管显示出来。-Parallel Port numeric keypad test requirements: master the dynamic display, dynamic scan the keyboard works and the hardware and software design, debugging the means to acquire 80C51 interface hardware circuit design methods and software programming approach to understanding the 80C51 external interrupts use and programming methods Experimental subjects: parallel port for digital 0 ~ 9, A ~ F, L, U, P, n total of 20 keyboard, the result will be keys to use 7-segment digital tube display.

AD 转换 用定时器中断 显示 0--5V-AD0804 zhongduan xianshi

控制电机运动的G代码程序,如果对G代码不清楚,请先看懂G代码,然后再看本程序.-Control motor movement, G code program, if the G code is not clear, please understand G code, and then look at the procedures.

这是一个在proteus下仿真成功的闪烁灯的例子。对于初级学习proteus的人很有帮助-This is a simulation in proteus success under the lights flicker example. For the initial study and the people very helpful proteus

PS2 读取键盘数具,非常好的一个软件PCB-PS2 keyboard to read a few, a very good software, PCB

用过采样和求均值技术提高模数转换器的分辨率.pdf-----针对目前单片机内嵌的模／数转换器的分辨率太低，而外接高分辨率成本又太高的情况，提出了用“过采样和求均值”的技术来使在有用的测量频带内的信噪比得到改善，从而提高测量的分辨. 率。并利用 60 - 7 0 /对其结论进行仿真，且在单片机上予以实现，结果表明测量分辨率明显提高。-Sampling and averaging techniques used to improve the resolution of ADC. Pdf----- targeted at the embedded microcontroller A/D converter resolution is too low, while the external high-resolution costs are too high situation, put forward with " Oversampling and Averaging" technology to make useful measurements in the frequency band signal to noise ratio to be improved, thereby enhancing the measurement resolution. rate. And a 60- 7 0/simulation of its conclusions, and in the SCM to be achieved, results show that the measurement resolution has improved significantly.

高速电路信号完整性问题，有一定的参考价值-Based on the Signal Integrality theory, the key problem met during signal processing module design and its solution is given