-
汇编子程序 大学课程设计需求者的最爱
汇编子程序 大学课程设计需求者的最爱-compilation subroutine university curriculum design needs a favorite
- 2023-04-11 00:55:03下载
- 积分:1
-
Stepper motor program control is a delicate describes the stepper motor work and...
经典的GPS原理书,有深度,并且有matlab实例-GPS classical principle of the book, depth, and have matlab examples
- 2023-04-11 03:15:33下载
- 积分:1
-
hard disk's master boot sector literacy program's source code can be use...
硬盘主引导扇区读写程序源代码,可用于读取硬盘主引导扇区的信息也可对其进行修改。-hard disk"s master boot sector literacy program"s source code can be used to read hard disk"s master boot sector information may also make changes.
- 2022-01-20 22:52:06下载
- 积分:1
-
电动车从起跑线出发(车体不得超过起跑线),沿引导线到达B点。在“直道区”铺设的白纸下沿引导线埋有1~3块宽度为15cm、长度不等的薄铁片。电动车检测到薄铁片时需...
电动车从起跑线出发(车体不得超过起跑线),沿引导线到达B点。在“直道区”铺设的白纸下沿引导线埋有1~3块宽度为15cm、长度不等的薄铁片。电动车检测到薄铁片时需立即发出声光指示信息,并实时存储、显示在“直道区”检测到的薄铁片数目。
(2)电动车到达B点以后进入“弯道区”,沿圆弧引导线到达C点(也可脱离圆弧引导线到达C点)。C点下埋有边长为15cm的正方形薄铁片,要求电动车到达C点检测到薄铁片后在C点处停车5秒,停车期间发出断续的声光信息。
(3)电动车在光源的引导下,通过障碍区进入停车区并到达车库。电动车必须在两个障碍物之间通过且不得与其接触。
(4)电动车完成上述任务后应立即停车,但全程行驶时间不能大于90秒,行驶时间达到90秒时必须立即自动停车。
-err
- 2022-08-04 00:05:12下载
- 积分:1
-
用汇编语言写的18B20写的温度测量和显示程序,采用LCD显示.
用汇编语言写的18B20写的温度测量和显示程序,采用LCD显示.-Written in assembly language using 18B20 written procedures for temperature measurement and display using LCD display.
- 2023-04-13 02:10:03下载
- 积分:1
-
On the compilation of 100 examples to facilitate the compilation of beginners, t...
关于汇编的一百个例子,方便汇编初学者,程序已可以通过-On the compilation of 100 examples to facilitate the compilation of beginners, the program has been through
- 2023-02-21 01:05:03下载
- 积分:1
-
计算今天星期几的汇编程序,没有用过程方法直接编写的程序...
计算今天星期几的汇编程序,没有用过程方法直接编写的程序-Today, a compilation of the calculation procedure a few weeks, there is no direct way to use the process of a program written in
- 2023-07-31 00:50:03下载
- 积分:1
-
memory of the presence of a compilation of source code
一个关于内存驻留的汇编源代码-memory of the presence of a compilation of source code
- 2023-04-08 21:05:03下载
- 积分:1
-
用8086汇编语言设计一存取款小软件系统。要求进入系统后,屏幕上显示“欢迎使用本系统”,另起行显示“输入密码:”。允许三次输入错误密码后可重新输入密码,三次输入...
用8086汇编语言设计一存取款小软件系统。要求进入系统后,屏幕上显示“欢迎使用本系统”,另起行显示“输入密码:”。允许三次输入错误密码后可重新输入密码,三次输入都出错则返回DOS。密码输入正确即进入本人帐号,并在屏幕上显示:
“1 返回DOS 2 查阅余额 3 存款 4 取款”
然后按1,2,3,4键选择所需工作方式。
以上各方式有如下功能:
1 返回DOS-- 退出小系统,返回DOS
2 查阅余额-- 显示本人帐号内余额(元)
3 存款-- 输入存款数目,即与余额相加
4 取款-- 输入取款数目,即与余额相减
按2,3,4键即进入相应方式,以ENTER键结束,结束后再显示:
"1 返回DOS 2 查阅余额 3 存款 4 取款"说明: ①屏幕显示可用英文,②帐号内要求可存额不小于十进制6位数
-wu
- 2022-06-18 05:07:00下载
- 积分:1
-
51控制led顺序点亮,
通过控制p0.0使其能按不同的顺序
51控制led顺序点亮,
通过控制p0.0使其能按不同的顺序
-Led the order of 51 to control light, through the control to enable them to p0.0 different order
- 2023-04-29 11:10:04下载
- 积分:1