uc/os2嵌入式实时操作系统详细技术文档，内核结构，任务管理都有比较详细的介绍...

LabVIEW在基于PCI控制卡的立体照片成像系统中的应用 基于LabVIEW和PCI-7422的数据采集系统设计 -LabVIEW-based PCI card controlling three-dimensional photo imaging system based on the application LabVI EW and PCI-7422 data acquisition system design

Link Establishment in Ad Hoc Networks Using Smart Antennas-Opnet_thesis

本分布式小区智能网络模型采用符合现场总线(Fieldbus)要求 的CAN技术，以带CAN总线端口的主控机和单元控制器CAN端接口构成的 CAN网络层，下层为由带RS485端口的住户采集器和单元控制器RS485端 接口构成了RS485网络层，向上则利用PC机连接CAN网络层，作为智能 化小区管理中心，从而基本实现智能小区管理、控制、报警、信息采 集和自我检测的功能。 本文从智能小区、现场总线、CAN技术到“CAN+RS485”双底层网 络模型的软、硬件研究，较为详细的介绍了其设计、调试运行和期间 各种问题的解决。 -The Distributed Intelligent Network model district in line with Fieldbus (Fieldbus) requirements CAN technologies to bring CAN bus port主控机and cell controller CAN-side interface consisting of CAN network layer, the lower the grounds with RS485 port Household acquisition and cell controller interface RS485 client constitutes a RS485 network layer, up modem to connect to the PC using the CAN network layer, as the Intelligent Community Management Center in order to realize the basic intelligent community management, control, alarm, information collection and self-testing function. This article from the Intelligent Community, Fieldbus, CAN technology to

Water meter interface with Jennic

MAX II CPLD具有灵活的可编程接口，合并了分立的FLASH存储器件，能快速和容易地配置FPGA，DSP，ASIC等。本中文手册将让用户对CPLD有一个宏观的认识。-MAX II CPLD with a flexible programmable interface, the merger of the separation of FLASH memory, can quickly and easily configure the FPGA, DSP, ASIC, etc.. Chinese manual will allow users to have a macro on the CPLD awareness.

设计一个可以顺计时和倒计时的秒表。要求计时的范围为00.0S~99.9S，用三位数码管显示，用三个发光二极管正确显示以下状态：倒计时状态、顺计时状态、待机状态-Designed to be a cis-timing and countdown stopwatch. Required time ranges from 00.0S ~ 99.9S, with three digital tube display, with three light-emitting diode display correctly the following states: the countdown state, cis-time status, standby mode

简易无线电遥控系统利用高频载频信号将调制信号经由发射端天线送出，在接收端经接收天线接收，再经过解调和解码恢复原信号用来控制发光二极管的亮灭。--Radio remote control system easy to use high-frequency modulated signal carrier frequency signal sent by the transmitter antennas, at the receiving end through the receiving antenna, and then through the demodulation and decoding to restore the original signal is used to control the brightness light-emitting diodes eliminate.--

主要给出msp430的程序代码，当然这只是嘴基本点程序集，具体程序代码还需要进一步涉及〉-MSP430 main program code is given, of course, this is only the basic point of the mouth assembly, the specific program code also needs to be further involved in

关于ssd的5篇经典文献，对于入门学习ssd的朋友应该十分有帮助。-5 ssd classical literature, for the entry of the ssd study should be very helpful friends.

这是基于LPC2000系统的CAN总线的应用，非常有使用价值。-This is based on the LPC2000 system CAN bus applications, very useful.