M3355的源代码，开发DVD的可以参考一下。

应用背景光学传感数字图像采集系统程序，本程序包含整个过程的程序，通过数组存放像素数据关键技术CX3芯片做主芯片  OV5640作为传感芯片  采集数据

嵌入式基于ARM的仿真软件skyeye的介绍和安装方法，及仿真linux的步骤。-ARM-based embedded software simulation skyeye the introduction and installation methods, and simulation steps linux.

《嵌入式系统构件》源代码-"embedded system components" source code

8051工作于11.0592MHZ,RAM扩展为128KB的628128,FlashRom扩展为128KB的AT29C010A 128KB的RAM分成4个区(Bank) 地址分配为0x0000-0x7FFF 128KB的FlashRom分成8个区(Bank) 地址分配为0x8000-0xBFFF 为了使8051能访问整个128KB的RAM空间和128KB的FlashRom空间,在CPLD内建两个寄存器 RamBankReg和FlashRomBankReg用于存放高位地址-8051 works in 11.0592MHZ, RAM expansion for the 128KB of 628128, FlashRom extended AT29C010A 128KB to 128KB of the RAM is divided into four zones (Bank) Address Assignment for the 0x0000-0x7FFF 128KB FlashROM divided into eight zones (Bank) Address Assignment for the 0x8000- 0xBFFF in order to enable the 8051 to access the entire 128KB and 128KB of RAM space of FlashROM space, two built-in CPLD register RamBankReg and used to store high FlashRomBankReg Address

MSP430F449与ATT7022开发的一款三相表demo，完善中，其中的几个程序模块，仅供参考。-MSP430F449 with the ATT7022 the development of a three-phase table demo, perfect, where several program modules for reference purposes only.

本程序是显示模块的例程，所接器件为四位八段led数码管，其中PTB0-PTB3 与数码管的位选相连接，PTB4，PTB5与74LS164连接确定你开发板上拨码开 关JP1（图片上的12）的两位和JP4（图片上的9）的5、6、7、8位处于on）， 而其他位处于远离on！-This procedure is the routine display module, the access device for four eight led digital tube, which PTB0-PTB3 bit digital tube and connected to the election, PTB4, PTB5 with 74LS164 sure you connect the development of on-board DIP switch JP1 ( picture on the 12) two and JP4 (picture on the 9) of 5,6,7,8 located at on), while the other located at far away from the on!

lwIP是瑞士计算机科学院（Swedish Institute of Computer Science）的Adam Dunkels等开发的一套用于嵌入式系统的开放源代码TCP/IP协议栈。Lwip既可以移植到操作系统上,又可以 在无操作系统的情况下独立运行.-lwIP Switzerland Computer Sciences (Swedish Institute of Computer Science), Adam Dunkels such as the development of a set of embedded systems for the open source TCP/IP protocol stack. Lwip can migrate to the operating system, can in no circumstances the operating system operate independently.

原创，采用简易JTAG版烧写基于ARM7的核的FLASH,4510板上测试通过-Original version of the summary JTAG programmer based on the ARM7 core of FLASH, 4510 on-board test

本系统分电压测量和信号产生输出两大部分，电压测量部分以模拟电路为主，配合放大模块、A/D转化模块、显示模块；通过凌阳单片机进行数据处理，在误差允许范围内显示测量电压值。信号产生以直接数字式频率合成器为核心，经过AT89S52对DDS芯片内部进行控制，使之输出标准正弦波形，利用编程实现频率预置、步进，达到电压输出频率的可调节步进。通过调试与测量完成了题目的基本部分和全部发挥部分的要求并有自己的创新。-Voltage measurement points of the system and the output of two major signals, voltage measurement circuitry to simulate the main part, with the amplification module, A/D conversion module, display module through Sunplus Single-chip data processing, in the range of error allowed shows the value of measuring voltage. Signal generated by direct digital frequency synthesizer for the core of the DDS chip AT89S52 after the internal control standards so that the output sine wave shape, frequency of use of pre-programming, step to the output voltage adjustable frequency step. Debugging and measurement, through the completion of the basic part of the topic and all the requirements to play a part and have their own innovation.

I2C 总线8 位远程I/O 扩展口芯片PCF8574 的原理与应用-I2C-bus 8-bit remote I/O expansion port of the PCF8574 chip Principle and Application