Real

CAN总线控制，SJA1000基本操作，keilC51开发环境-CAN bus control, SJA1000 basic operation, keilC51 Development Environment

步进电机加减速计算 说明输入步进电机的加减脉冲步数,就可计算出电机加减速的静态表(16进制输出)-motor s type download

P串行实时时钟芯片DSl302程序设计中的问题与对策-P serial real-time clock chip DSl302 program design problems and countermeasures

DownLoad_sst39sf010.zip--嵌入式系统中关于SST39SF010的FLASH的BOOTLOADER源程序(KC51)-DownLoad_sst39sf010.zip--embedded system on the FLASH SST39SF010 source of BOOTLOADER (KC51)

C8051F06X单片机编程，看门狗模块源代码-C8051F06X microcontroller programming, the watchdog module source code

1602LCD显示c51-1602LCD show C51

完整的ＴＣＳ控制系统原程序．包含系统检测，数据采集（Ａ－Ｄ）与处理，通信和回路控制与检测．产品已上市．-integrity of the original control system procedures. Includes system testing, data acquisition (A-D) and processing, communication and loop control and detection. Products are listed.

用C51实现的拼音输入法,这是改写的网友 embuffalo、独步上载在www.21ic.com自由发布区的由张凯原作的51上的拼音输入法程序。 原作使用了一个二维数组用以查表，我认为这样比较的浪费空间，而且每个字表的索引地址要手工输入，效率不高。所以我用结构体将其改写了一下。就是大家现在看到的这个。 因为代码比较的大，共有6,000多汉字，这样就得要12,000 byte来存放GB内码，所以也是没办法的 :-( 编译结果约为3000h,因为大部分是索引表，代码优化几乎无效。 在Keil C里仿真芯片选用的是华邦的W77E58，它有32k ROM, 256B on-chip RAM, 1K on-chip SRAM (用DPTR1指针寻址,相当于有1K的片上xdata)。条件有限，没有上片试验，仿真而已。 打算将其移植到AVR上，但CodeAVRC与IAR EC++在结构体、指针的定义使用上似乎与C51不太一样，现在还未搞定。还希望在这方面有经验的网友能给予指导。-C51 with the Pinyin input method, which is rewritten netizens embuffalo. Unrivaled www.21ic.com available in the free publication of the original work by Kai-51 on the Pinyin input method procedures . Appreciate the use of a two-dimensional array for the look-up table, I think this is a waste of space. Each of the characters but the index table to manually input address, efficiency is not high. I use the structure to rewrite a bit. We see now is this. Because the code comparison, a total of 6, more than 000 Chinese characters, this must

stc单片机的iap程序，用c51写的，是从汇编转换过来的-SCM STC IAP procedures, using C51 write is from the compilation of the conversion from the

arm7定时器中断方式，可以通过中断方式实现定时的功能-ARM7 interrupt timer, it can be achieved through the disruption of the function of timing