登录
首页 » 汇编语言 » 本程序为调用系统时钟设计的一个汇编语言写的时钟程序

本程序为调用系统时钟设计的一个汇编语言写的时钟程序

于 2022-08-13 发布 文件大小:11.98 kB
0 199
下载积分: 2 下载次数: 1

代码说明:

本程序为调用系统时钟设计的一个汇编语言写的时钟程序-the procedures called for the system clock design an assembly language to write the clock procedures

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 中断列表(5) : 工具程序 265K
    中断列表(5) : 工具程序 265K-suspended list (5) : Tools procedures 265K
    2022-02-07 00:28:50下载
    积分:1
  • masm old fargon 2 to do asmbly code
    masm old fargon 2 to do asmbly code
    2022-12-15 09:55:02下载
    积分:1
  • Python对文件IO操作
    filePath="c:/test/tt.txt" #从文件中读取信息 f=open(filePath, "r")#运用读的方式打开文件, for line in f: #每次读取文件的一行内容      print(line) f.close() #向文件中写入信息 f=open(filePath, "a") #这里有两种方式:第一种是以w的形式,它写入时将会清空以前的数据然后再写入数据,第二种是以a的形式,它以追加的形式写入数据 f.write("我开始向文件中写入信息 ") f.writelines("我已经向文件写入了信息") f.close()
    2022-03-02 22:46:33下载
    积分:1
  • 0到99秒的计时,误差极小,不同一般的DELAY哦.
    0到99秒的计时,误差极小,不同一般的DELAY哦.-0-99 seconds of the time, the error is very small and different from other DELAY oh.
    2022-08-25 15:19:00下载
    积分:1
  • dos memory management sample
    dos memory management sample
    2023-05-10 00:55:05下载
    积分:1
  • eight wasted lights function of the sample program, the eight RB pin all set to...
    8位流水灯实例程序 功能是,将RB的8条引脚全部设置为输出模式,依次从RB0到RB7送出高电平,然后再依次从RB7到RB0送出高电平.并且周而复始-eight wasted lights function of the sample program, the eight RB pin all set to output mode, followed from RB0 RB7 to send serial, From then followed RB0 RB7 to send margin. and the cycle
    2022-12-25 08:30:03下载
    积分:1
  • 用汇编语言编程,环境为keilC开发环境,显示温度
    用汇编语言编程,环境为keilC开发环境,显示温度-Using assembly language programming, the environment keilC development environment, shows that the temperature
    2022-08-16 12:39:28下载
    积分:1
  • 是非颠倒收发撒的发送方式大法师的方式答复撒 的算法是地方...
    是非颠倒收发撒的发送方式大法师的方式答复撒 的算法是地方 -Non-reversal mode transceiver Caesar sent the way of responding to large Master sprinkle the algorithm is place
    2022-06-17 00:05:19下载
    积分:1
  • Beginning to show 00 , 1st press SP1 after the beginning of time. 2nd by SP1, t...
    开始时,显示“00”,第1次按下SP1后就开始计时。 第2次按SP1后,计时停止。 第3次按SP1后,计时归零。 -Beginning to show 00 , 1st press SP1 after the beginning of time. 2nd by SP1, the time to stop. The 3rd by SP1, the time zero.
    2022-11-05 23:25:03下载
    积分:1
  • 这个源
    This the source-code of a 64k-intro. Run it through tasm and tlink, and it will work (the makefile will also work). ----------------------------------------------------------------------- -This is the source-code of a 64k-intro. Run it through tasm and tlink, and it will work (the makefile will also work). ----------------------------------------------------------------------- -----------------------------------------------------------------------
    2022-03-29 20:12:24下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载