24位AD芯片TM7710 演示程序 *单片机型号： STC5624AD *晶 震 ： 12M...

STCS89C51单片机的介绍，给热爱STCS89C51的朋友提供一个参考资料。-SCM STCS89C51 introduction to the love of friends STCS89C51 to provide a reference.

此程序为单片机开发过程中定时芯片ds1302的控制并用lcd显示的程序，用汇编语言编写。供参考用-procedure for microcontroller development process of regular chips ds1302 control and LCD display with the procedures in assembler language. For information

P1.7～P1.0接发光二极管L8～L1，要求利用单片机内部定时器1，按方式1工作，每0.01秒T1溢出中断一次。要求编写程序模拟时序控制装置。开机第1秒钟L1、L3亮，第2秒钟L2、L4亮，第3秒钟L5、L7亮，第4秒钟L6、L8亮，第5秒钟L1、L3、L5、L7亮，第6秒钟L2、L4、L6、L8亮，第7秒钟8个发光二极管全亮，……一直循环下去。fosc=11.0592MHz-P1.7- P1.0 then LED L1 to L8, by using a timer internal microcontroller, a work by the way, every 0.01 seconds T1 interrupted an overflow. Simulation prepared timing control device. Boot 1 seconds L1, L3- liang, two seconds L2- L4, L5 three seconds, L7- liang, 4 seconds L6, L8-liang, 5 seconds L1, L2, L5, L7- liang, 6 seconds L2, L4, L6, L8- , 7 seconds 8-LED whole ... has been the cycle continues. 11.0592MHz fosc =

PIC16F877控制DS1302时间芯片 ds1302时间芯片-PIC16F877 chip control DS1302 time ds1302 time chip

AT89C51的有关语音芯片-isd4004的驱动程序-AT89C51 voice chip on the driver-isd4004

PROFIBUS从站智能协议芯片DPC31与模数转换器AD7705接口设计.rar-PROFIBUS slave smart chip DPC31 agreement with the AD7705 ADC interface design. Rar

无刷直流电机控制程序，通过PIC18F2431控制。-Brushless DC motor control program, through the PIC18F2431 control.

STK500_2下载器 M8 支持bootloader(带bootloader源码) 使用STK500_2 协议的ISP下载器，监控芯片 M8,数据通讯RS232.使用 ATMEL AVRStudio 4.xx STK500工具的进行软件升级。可通过ATMEL AVRStudio 4.xx STK500工具升级固件程序。升级方法：通过设定电压 即按“write voltage”按钮进入bootloader程序。 -M8 browser support STK500_2 download bootloader (with bootloader source code) to use the ISP to download STK500_2 agreements, and monitor chip M8, data communication RS232. Use ATMEL AVRStudio 4.xx STK500 tool for software upgrades. By ATMEL AVRStudio 4.xx STK500 firmware upgrade tool. Upgrade methods: by setting the voltage that is, according to

这是一个实现利用gsm模块通信的visual basic 源程序-This is a system to use the gsm module communications, visual basic source code

I2C串行总线元器件标准驱动程序的编写，可自己定义串行时钟线和串行数据线所在口-I2C serial bus driver standard components of the preparation, may own definition serial clock line and serial data line I