ADE7758的相关程序，包括对ADE7758的读写，以及校准程序

KeilC51 下作的8*8LED显示程序。更改delay()时间和tab*表中的值，可以显示不同的图形-KeilC51 under the 8* 8LED display program. Change the delay () time and tab* in the table values, you can display different graphics

keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.

MCF5272的评估版原理图和PCB图嵌入式硬件设计资料-MCF5272 evaluation version of the schematic and PCB map embedded hardware design information

430所有的演示程序示范，教科书式的编写规范-430 all the demo model, the textbook-style preparation of normative

电子定时器的设计 有程序的具体实现和功能描述 好的程序-electronic timer with the design of specific procedures to achieve good functional description and procedures

这是一个10的A/D转换芯片，用他与51单片机组成控制系统，具有结构简单，系统稳定的特点。-This is a 10 A/D converter chips, and with his 51 MCU control system is simple in structure, system stability characteristics.

用LPC93251操作nand flash K9F6408，能正确擦，写，读。改用其它芯片，方法类似，注意时序就行了。如换用大容量flash，请注意每块的页数，6408每块是16页的。-with LPC93251 operation nand flash K9F6408 can correct rub, writing and reading. Other chip switch, a similar manner, the attention on the timing of the trip. If used for large-capacity flash, to every piece of pages, 6,408 each block is the 16.

sja1000与串口通信的程序，用串口通信助手可观察结果-SJA1000 with serial communication procedures, using serial communication assistant can be observed

功能：1 实时绘制数据曲线2 保存接受数据到文件3 能在各种参数下，与单片机和pc机通过串口通讯4 能实时记录输入和输出数据sstcomc.c为单片机上使用的演示程序，在keil c51编译以后，在sst89c58测试通过-functions : a real-time rendering two data curves accept data preservation of documents in three parameters, and SCM and PCs through four serial communications can be captured in real time input and output data for SCM sstcomc.c demonstration on the use of procedures, the Keil compiler decoder, after the sst89c58 the test

12864最权威的资料，两个资料一起组成完整资料-12864 most authoritative information, with information on the composition of two incomplete information