洗衣机程序 普通的家用洗衣机的大部分功能都可以实现 但其中有更好的设计 望指教...

此为AD转换器ADC0809的资料-this AD converter for the ADC0809

两片max7219的串联编程 编程语言为汇编语言-two max7219 Series programming language programming language for compilation

八位CRC,c程序-eight CRC, c procedures

自动交通管理系统 用红、绿、黄三支共两组发光二极管表示交通信号灯，利用单片机模拟有时间显示的定时交通信号灯控制管理。信号灯的变化规律可如下： 1）放行线：绿灯亮放行25秒，黄灯亮警告5秒，然后红灯亮禁止。 2）禁止线：红灯亮禁止30秒，然后绿灯亮放行。 3）当某一方向的红灯亮时，若该方向有车通过，则用扬声器声报警。（撞红灯信号可用3-5V模拟量表示） 同时用2位数码管进行30秒钟递减时间显示。-automatic traffic management system using red, green, yellow a total of three light-emitting diodes, said two traffic lights, using SCM time simulation shows the regular traffic signal control. Signal changes in the law to be as follows : 1) Release Line : green clearance 25 seconds, bright yellow warning five seconds, and then the red-ban. 2) prohibit the lines : red-Ban 30 seconds, then green clearance. 3) When the red light in one direction- that if the direction of a car passed, the use of loudspeakers sound alarm. (Red light signals can hit 3- 5V analog said), while using two digital tube for 30 seconds decreasing time displayed.

51io模拟串口程序-51io simulation procedures

Atmel Uart C51程序（timer1方式）-Uart (timer1 way)

这是AD转换芯片AD7705的初始化程序，主要是寄存器的配置-This is the AD conversion chip AD7705 initialization procedure is the configuration register

遥控数字钟应用程序，应用于多种数字钟接口，可以遥控设备，省力。自制LED电子钟在很多电子报刊杂志上都可以见到，但大多数在断电后都要重新设置时间等 参数，给使用带来很多不便。也有用后备电池作为备用电源的，但往往体积较大。本文介绍 的LED电子钟克服了以往的弊端，而且采用了家电通用的红外遥控器进行控制，方便使用。 有一路闹铃输出，可以通过遥控器设置闹铃时间及允许与否。-digital clock remote control applications, digital clock used in a variety of interface, remote-control equipment, effort. Homemade LED electronic bell in many electronic newspapers and magazines can all, but most of the power outages after the re setup time and other parameters to use in many ways. Also useful as a standby battery backup power, but often larger. This paper introduces the LED electronic clock to overcome the shortcomings of the past, and the use of common household appliances infrared remote control, and ease of use. A way Alarms output, the remote control can set the alarm time and allow it or not.

单片机工业控制板,具备I/O,KEYBOARD,步进电机伺服电机等功能-SCM industrial control panel, with I/O, KEYBOARD, stepper motor servo motor function

MSP430 149的4×4键盘扫描程序（中断方式），以及JM12864M的液晶驱动程序，谢谢指教-MSP430 149 of 4 × 4 keyboard scan program (interrupt mode), as well as LCD driver JM12864M Thank you advice