Protel shortcuts. Protel Cabling improve the speed of a good information

采用2051单片机控制的红外解码程序，采用汇编语言实现-2051 MCU control using infrared decoding procedures, using assembly language to achieve

包含Realview mdk2_3_链接.swf RealView MDK链接及调试.swf Realview_mdk2_1开发环境的建立.swf Realview mdk2_4_模拟仿真.swf Realview mdk#1.swf Realview_mdk2_2启动代码概述.swf 学习STM32的有用-With Realview mdk2_3_ link. Swf RealView MDK links and debugging. Swf Realview_mdk2_1 development environment for the establishment. Swf Realview mdk2_4_ simulation. Swf Realview mdk# 1.swf Realview_mdk2_2 an overview of the boot code. Swf to study the usefulness of STM32

用于向51单片机和ARMlpc系列单片机下载程序-For the 51 Series Single-chip MCU and ARMlpc download

BTF020实验程序-1 btf020开发板自带-Experimental procedures BTF020 development board comes with-1 btf020

采用IAR进行编译。 这是ATMEGA128单片机的BOOTLOADER的源码。 和AVRSTUDIO配合使用。 具体请参考bootloader.c的注释说明。 如有任何问题请邮件联系。-used for IAR compiler. This is ATMEGA128 SCM BOOTLOADER source. And the use of AVRSTUDIO tie. Please refer to specific bootloader.c note of the Notes. If you have any questions please contact mail.

触摸屏芯片ads7846ads7843驱动程序(C语言编写），单片机控制的触摸屏驱动程序（C编写）-Touchscreen chip ads7846ads7843 Driver (C language), SCM control Touchscreen Driver (C preparation)

ATMEL的24C04-512的通用应用程序，实际应用完全可行可靠的，稍加修改就可用在自己的C文档中！-ATMEL

这是参加电子设计大赛时的作品：红外遥控小车：用红外线通过一块AT89S52单片机发射信号即编码，并用红外接收头接收信号；接着再用另一块AT89S52单片机对红外发射出的信号编码进行解码，最后再用一块AT89S52单片机用解码所得码值编写程序后驱动步进电机。步进机功能启动后不仅能使受控小车向前后左右四个方向前进和转弯，而且还能控制小车再地上转动并留下方形或圆形等形状。-This is the time to participate in Electronic Design Contest works: infrared remote control car: Using infrared transmission signal through an AT89S52 microcontroller that is encoded and used infrared receiver to receive the first signal and then using the other an infrared emitting MCU AT89S52 code and decode the signal and finally an AT89S52 microcontroller then proceeds with the decoding key value of the preparation of procedures to drive a stepper motor. Stepper machine function activated not only make the car forward in a controlled direction and after about four turns, but also to control the car and then turned and left the ground such as square or round shapes.

Motorola MCU HC08下的uCOSII移植源代码，刚刚完成。附用户应用程序测试，稍加修改可以增加自己功能。-HC08 Motorola MCU under uCOSII transplant source code, has just been completed. A user application procedures for the testing, a little change can increase their functionality.

点阵LED显示0-9程序（c语言）,此程序为8*8LED点阵的简单程序-Dot-matrix LED display 0-9 program (c language)