DS18B20,我已经做过,显示正确!欢迎下载!

无线模块TC35I开发必用，详细的AT指令手册-Wireless module TC35I development will use a detailed instruction manual for AT

MEGA16的小车沿黑线行驶程序，能够控制程控小车沿规定路线自行行使。-MEGA16 the black car along the lane, it will be programmed control along the trolley line provides free exercise.

89S52加USBD12模拟的一个U盘（源码+原理图+实物照片） Computer00 发表于 2006-3-3 14:09:00 USB-D12文件包下载.rar 这是一个用89S52加PDIUSBD12模拟的一个U盘，里面涉及到USB接口，USB大容量存储设备，FAT16文件系统等内容。插入电脑后，可显示移动磁盘盘符及一个文本文件。 需要说明一下的是，这个包中的原理图，IDE接口部分、74HC573、以及RS232串口等部分，是作为这个实验板的一部分。在这个模拟U盘的程序中，是没有用到的。在下一个“移动硬盘”的例子中，就用到了IDE接口跟74HC573了。至于RS232，那时笔者在调试程序时用的。如果您不需要通过串口调试程序，RS232部分可以不管它-89S52 increase USBD12 simulation of a U-Disk (OSS diagram kind photos) Comput. er00 published in 2006-3-3 14:09 : 00 USB-D12 package downloaded. rar This is a plus with 89S52 simulation PDIUSBD12 of a U disk, which relate to the USB interface, USB mass storage devices, and FAT16 file system and so forth. Insert the computer, can show that the mobile disk drive and a text file. Need to point out that this is a package of drawings, IDE interface, 74HC573. and RS232 serial port as part of the experiment as part of the plate. In this simulation U disk process is not used in the. Next a "mobile hard" cases, the option of the IDE int

ARM7开发板的USB源程序，好东西咯。 -ARM7 development board

this a store management system-this is a store management system

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

sed1335液晶驱动器源码，cpu为摩托罗拉16位单片机MC9S12DT128-sed1335 LCD driver source code for Motorola cpu 16 SCM MC9S12DT128

音乐兰花草播放演示，汇编编写，用的是扬声器，不是蜂鸣器!-Music orchids player demo, compilation of writing, using a speaker, not the buzzer!

CAN总线调试通过的程序，SJA1000芯片的Peli CAN模式下的C51源程序-CAN bus debug the procedure adopted, SJA1000 chip Peli CAN mode source of C51

基于C8051F340的AD转换和1602液晶显示的测试小程序-Based on the C8051F340 of AD conversion and 1602 LCD test applet